Thursday, 10 March 2011 15:13

Rice

Rice is the staple food for Asian people; it is prepared by cooking or ground as flour for bread making, thus helping to feed the rest of the world population. Various kinds of rice are produced to suit the taste of the consumers. Rice cultivation is done either in marshy, lowland areas with plenty of water or in plateau or hilly regions where natural rainfall provides adequate amounts of water.

Cultivation Process

Rice can be cultivated either by hand or by partial or full mechanization, according to the technological development of the country and the need for productivity. Whatever kind of operation is done, the following step-by-step processes are necessary.

  1. Ploughing. The land is ploughed in three stages to eliminate lumps and to make soil as soft and muddy as possible. Buffalo, oxen or cows usually pull the ploughs, though the use of mechanical equipment is increasing.
  2. Weeding is carried out three times by irrigating the land for 5 days at a time and then letting it dry for 5 days. At the end of each cycle, the land is beaten with a heavy wooden tool to kill off young weeds so they may be used as natural fertilizer.
  3. Preparation of seedlings. The seeds are soaked in a large water-filled jar with appropriate concentrations of salt added to make the healthy seeds sink. These healthy seeds are then thoroughly washed, soaked overnight, wrapped in a thick cloth or sack for 2 nights to germinate, sown in the area prepared for them and left to grow for approximately 30 days.
  4. Transplantation. The young plants, in bunches of 3 to 5, are thrust into the mud in rows and grown for 10 days. After about a total of 45 days, the plant is fully grown and begins to bear seeds.
  5. Harvesting. When the plant is about 100 days old, it is usually reaped by hand (see figure 1); sickles or similar tools are used for cutting the bearing grains off.
  6. Drying is done in the open air in the sun, to make the moisture content fall below 15%.
  7. Threshing separates the grain, with its husk or glume, from the stalk. Traditionally, buffaloes or oxen are used to slowly drag the threshing combs over the stalk to force out the grain. Many places use locally made machines for this.
  8. Storage. Grains and hays are stored in barns or silos.

 

Figure 1. Harvesting of rice plants by hand in China, 1992

AGR130F8

Lenore Manderson

Hazards

Common and specific hazards are as follows:

  • Poor housing, low sanitary standards, inadequate nourishment and the need to drink large quantities of water, which is not always pure, lead to general weakness and fatigue, possible sunstroke, intestinal troubles and diarrhoea.
  • Most injuries caused by farm machinery occur when the workers are not familiar with the machines. Muscles, bones and joints are intensively used, both in dynamic and static loads, causing physical fatigue and resulting in the reduction of work capacity and an increase in traumatic injuries and accidents. Children and adolescents, as well as migrant workers, die from farm injuries each year.
  • Chemical agents, such as fertilizers, strong weedkillers, pesticides and other extensively used substances, increase the hazards both for the workers and the animal or plant foods they consume (e.g., fish, field crabs, water plants, mushrooms, medicinal herbs, field rats or even contaminated water).
  • Diseases (e.g., malaria, tetanus, hookworm, schistosomiasis, leptospirosis, hay fever, farmer’s lung, dermatitis, blepharitis, conjunctivitis, common cold and sunstroke) are very common, as are nutritional disorders (e.g., protein deficiency, toxins), alcoholism, heavy smoking and other addictive habits.
  • The most common occupational diseases are skin diseases. These include: redness and blisters from prickly rice leaves; abrasions and skin injuries caused by prickly plants; calluses of the palms, hands, knees and elbows caused by bad posture and the use of hand tools; skin fungal infections (tinea) due to epidermophytes and Monilia (candida), which may be complicated by secondary sensitization, redness and blisters, frequently due to Staphylococcus bacteria; vesicular dermatitis (small blisters) on the feet sometimes attributed to Rhizopus parasiticus; itch commonly caused by the penetration of the skin by Ancylostoma (hookworms); schistosome dermatitis caused directly or indirectly by contact with water containing blood flukes from nonhuman hosts; and redness, blisters and oedema resulting from insect stings.
  • Respiratory diseases due to organic and inorganic dusts and synthetic chemicals are common. Gram-negative bacterial endotoxin levels in air are high in some countries. Silage gas poisoning of high nitrate soils is also a health problem.
  • Climatic agents such as heat, heavy rain, humidity, high wind, storms and lightning strike both workers and cattle.
  • Psychological stress factors such as economic problems, sense of insecurity, lack of social standing, lack of educational opportunities, lack of prospects and risk of unexpected calamities are particularly common in the developing countries.

 

Safety and Health Measures

Working conditions should be improved and the health hazards reduced through increased mechanization. Ergonomic interventions to organize the work and working equipment, and systematic training of the body and its movements to ensure good working methods, are essential.

Necessary medical preventive methods should be strictly applied, including the introduction of first aid instruction, the provision of treatment facilities, health promotion campaigns and medical surveillance of workers.

Improvement of housing, sanitary standards, accessible potable water, nutritional environmental hygiene and economic stability are essential for the quality of life of rice field workers.

Applicable International Labour Organization (ILO) Conventions and Recommendations should be followed. These include:

  • The Minimum Age (Agriculture) Convention, 1921 (No.10), provides that children under the age of 14 years may not be employed or work in any public or private agricultural undertakings, or in any branch thereof, when school is in session.
  • The Night Work of Children and Young Persons (Agriculture) Recommendation, 1921 (No.14), requires that each Member State regulate the employment of children under the age of 14 years in agricultural tasks at night, leaving not less than 10 consecutive hours for them to rest. For young persons between the age of 14 and 18 years, the period of rest must consist of not less than 9 consecutive hours.
  • The Plantations Convention, 1958 (No.110), provides that every recruited worker shall be medically examined. This Convention is obviously of great importance for workers of all ages.
  • The Maximum Weight Convention, 1967 (No.127), identified optimum loads that can be handled by 90% of workers for all routine and repetitive manual-handling tasks.

 

Back

Thursday, 10 March 2011 15:11

Case Study: Agricultural Machinery

Adapted from 3rd edition, “Encyclopaedia of Occupational Health and Safety”.

Agricultural machinery is designed to till the soil and render it more suitable for crop growth, to sow seeds, to apply agricultural chemicals for improved plant growth and control of pests and diseases, and to harvest and store the mature crops. There is an extremely wide variety of agricultural machines, but all are essentially a combination of gears, shafts, chains, belts, knives, shakers and so on, assembled to perform a certain task. These parts are usually suspended in a frame which may be either stationary or, as is more often the case, mobile and designed to perform the desired operation while moving across a field. The major groups of agricultural machines are: soil tillage machines; planting machines; cultivating machines; forage harvesting machines; grain, fibre, vegetable, and fruit and nut harvesting machines; agricultural chemical applicators; transport and elevating machines; and sorting and packaging machines.

Soil tillage machines. These include ploughs, tillers, subsoilers, harrows, rollers, levellers, graders and so on. They are designed to turn, agitate, level and compact the soil to prepare it for planting. They may be small in size and require only a small power source (as in the case of a one-person roto-tiller for tilling a rice paddy), or they may be large and require a considerable power source (as in the case of a combined subsoiler, drill and harrow).

Planting machines. These include planters, drills, broadcast seeders and so on and are designed to take seeds from a hopper or bin and insert them in the soil at a predetermined depth and spacing or spread them uniformly over the ground. Planters may be of simple design and comprise a single-row seeding mechanism, or they may be highly complex (as is the case with the multi-row planter with attachments that simultaneously add fertilizer, pesticides and herbicides).

Cultivating machines. These include rotary hoes, cultivators, weeders (mechanical and flame) and so on. They are used to eradicate undesirable weeds or grasses which compete with the plant for soil moisture and make the harvest of the crop more difficult. They also improve the soil tillage so as to make it more absorptive of rain.

Forage harvesting machines. These include mowers, choppers, balers and so on and are designed to sever the stems of roughage crops from their roots and prepare them for storage or immediate use. The machines also vary in their complexity: the simple mower merely cuts the crop, whereas the chopper will not only separate the stalk from the root but will also chop the entire plant into small pieces and load it into a vehicle, which may be a towed wagon. Crimpers, which crush or break the stems of plants, are often used to expedite the field-drying process of fodder crops to prevent spoilage, especially of legumes that will be placed in dry storage or baled. Pelleting machines are used to compress fodder crops into compact cubes for mechanical feeding of livestock. Balers are used to compress fodder into square or round bales to facilitate storage and handling. Some bales are small enough (20 to 40 kg) to handle manually, while others may be so large (400 to 500 kg) as to require mechanical handling systems.

Grain and fibre harvesting machines. These include reapers, binders, corn pickers, combines, threshers and so on. They are used to remove the ripe grain or fibre from the plant and place it in a bin or bag for transport to the storage area. Grain harvesting may involve the use of a number of machines, such as a reaper or binder to cut the standing grain, a wagon or truck to transport the crop to the threshing or separating machines and vehicles to transport the grain to a storage area. In other cases many of these functions may be performed by a single machine, the combine harvester (figure 1), which cuts the standing grain, separates it from the stalk, cleans it and collects it in a bin, all while moving through the field. Such machines will also load the grain into transport vehicles. Some machines such as cotton pickers and corn pickers may operate selectively and remove only the grain or fibre boll from the stem or stalk.

Figure 1. Combine for harvesting wheat without an enclosed cabin.

AGR070F5

Vegetable harvesting machines. These include diggers and lifters, and are designed either to dig the crops from the earth and separate them from the soil or to lift or pull the plant free. The potato digger, for example, may form part of a potato combine comprising a sorting, grading device, polisher, bagger and elevator. At the other extreme is the simple two-wheeled, bladed sugar-beet lifter which is followed by hand labourers.

Fruit and nut harvesting machines. These machines are used to harvest berries, fruit and nuts. They may be as simple as a tractor-mounted, vibrating tree shaker which separates the ripe fruit from the tree. Or they may be as complex as the ones which harvest the fruit, catch the falling fruit, place it in a storage container and later transfer it to transport vehicles.

Transport and elevating machines. These also vary considerably in size and complexity ranging, for example, from a simple wagon comprising merely a platform on wheels to a self-loading and stacking transport unit. Inclined chain, flight or belt conveyors or other mechanical handling devices are used to move bulky material (hay, straw, ear corn and so on) from wagon to storage or from one location in a building to another. Screw conveyors are used to move granular material and grain from one level to another, and blowers or pneumatic conveyors are used to move light materials horizontally or vertically.

Agricultural chemical applicators. These are used to apply fertilizers to stimulate plant growth or herbicides and pesticides to control weeds and pests. The chemicals may be liquid, powdered or granular, and the applicator distributes them either by pressure through a nozzle or by centrifugal force. Applicators may be portable or vehicle-mounted; the use of aircraft for chemical application is growing rapidly.

Sorting and packaging machines. These machines are usually stationary. They may be as simple as a fanning mill, which grades and cleans grain merely by passing it over a series of screens, or as complex as a seed mill, which will not only grade and clean but also, for example, separate different types of seeds. Packaging machines usually form part of a sophisticated grading system. They are used primarily for fruit and vegetables and may wrap the produce in paper, bag it or insert it into a plastic container.

Power plants. Electric motors may be used to drive stationary equipment permanently located near a mains supply; however, since many agricultural machines are mobile and must operate in remote areas, they are usually powered by an integral petrol engine or by a separate engine such as that of a tractor. Power from a tractor may be transmitted to the machine via belt, chain, gear or shaft drives; most tractors are fitted with a power take-off coupling specially designed for this purpose.

 

Back

Thursday, 10 March 2011 15:05

Mechanization

The mechanization of agricultural work and work processes has relieved many workers throughout the world of onerous, back-breaking, monotonous labour. At the same time, the speed and power associated with mechanization contributes greatly toward serious traumatic injury. Throughout the world, countries that practise mechanized agriculture list tractors and field and farmstead machinery as leading agents of fatal and disabling injury in agricultural work. Power tools also contribute to the injury toll, though these injuries are usually less severe. Some machinery also presents environmental hazards such as noise and vibration.

Tractor hazards

Farm tractors have many characteristics that result in their being the most important piece of power equipment on the farm. Most tractors have rubber tyres, hydraulic systems, and power take-off (PTO), and utilize a combination of engine speeds and gear ratios. These characteristics combine to provide tractors with speed, power, flexibility and adaptability. The most serious hazards associated with tractor operation include overturns, runovers and PTO entanglement. Tractor overturns fatally injure far more victims than any other type of incident. Table 1 provides a listing of tractor hazards and how injuries occur.

Table 1. Common tractor hazards and how they occur

Hazard

Type of incident

How injury occurs

Overturns

Side rollovers

Operating on slopes, turning corners too fast, rear wheel drops into a hole or off-road surface.

 

Rear rollovers

Hitching to a point other than the drawbar, rear wheels are stuck in mudhole or are frozen to the ground.

Runovers

Passenger (extra rider) falls off

Most tractors are designed only for one operator; therefore, there is no safe location for an extra person on a tractor.

 

Operator falls off

Knocked off by low-hanging tree limb, bounced out of seat by traversing rough ground.

 

Operator is run over while standing on the ground

Jump starting tractor with tractor inadvertently in gear. Tractor rolls while mounting/dismounting. Tractor rolls during hitching/unhitching of equipment.

 

Bystander or on-ground helper is run over

Bystander incidents often involve small children the operator does not see. On-ground helper incidents are similar to operator-on-the-ground incidents.

Power take-off (PTO)

Entanglement with PTO stub shaft

Master shield is missing and PTO is left engaged while tractor is running. Operator may be mounting/dismounting from rear of tractor.

Slips and falls

Mounting/dismounting from tractor

Wet and/or muddy feet, first/last step is high off the ground, difficult to reach handholds, hurrying, facing wrong way when dismounting.

Noise-induced hearing loss

Operating tractor

The tractor muffler may be missing, damaged, or is a non-recommended replacement; tractor engine is not maintained properly; metal weather cab redirects sound back to the operator. Damaging noise level may come from a combination of tractor and attached machine. (Older tractors generally produce louder sounds than newer tractors.)

 

Overturns

The central concept in tractor stability/instability is centre of gravity (CG). A tractor’s CG is the point on the tractor where all parts balance one another. For example, when a two-wheel-drive tractor is sitting with all wheels on level ground, the CG is typically about 25.4 cm above and 0.6 m in front of the rear axle and in the centre of the tractor body. For four-wheel-drive and centre-articulated tractors, the CG is located slightly more forward. For a tractor to stay upright, its CG must stay within the tractor’s stability baseline. Stability baselines are essentially imaginary lines drawn between points where tractor tires contact the ground (see figure 1). A tractor’s CG as such does not move, but its relationship with stability baselines may change. This most often occurs as the tractor moves out of a perfectly level position, such as onto a slope. A changing relationship between CG and stability baseline means the tractor is moving toward an unstable position. If the CG-stability baseline relationship changes significantly (e.g., the tractor CG moves beyond the stability baseline), the tractor rolls over. If equipment such as a front-end loader, a round bale lifting fork or a chemical side-saddle tank is mounted on the tractor, the additional weight shifts the CG toward that piece of equipment. As mounted equipment is raised, the CG is raised.

Figure 1.  The stability baseline of a tricycle tractor and a wide front-end tractor, respectively

AGR110F1

Other factors important to tractor stability/instability include centrifugal force (CF), rear-axle torque (RAT) and drawbar leverage (DBL). Each of these factors works through the CG. Centrifugal force is the outward force nature exerts on objects that move in a circular fashion. Centrifugal force increases both as the turning angle of the tractor becomes sharper (decreases) and as the speed of the tractor increases during a turn. The CF increase is directly proportional to the turning angle of the tractor. For every degree the tractor is turned tighter, there is an equal amount of increased CF. The relationship between CF and tractor speed, however, is not directly proportional. Finding the increase in CF from turning a tractor at a higher speed                                                                                                                                       (assuming the turning radius stays the same) calls for squaring                                                                                                                     the difference between the two tractor speeds.

RAT involves energy transfer between the tractor engine and the rear axle of a two-wheel-drive tractor. Engaging the clutch results in a twisting force, called torque, to the rear axle. This torque is then transferred to the tractor tyres. Under normal circumstances, the rear axle (and tyres) should rotate, and the tractor will move ahead. In lay terms, the rear axle is said to be rotating about the tractor chassis. If the rear axle should be unable to rotate, the tractor chassis rotates about the axle. This reverse rotation results in the front end of the tractor lifting off the ground until the tractor’s CG passes the rear stability baseline. At this point the tractor will continue rearward from its own weight until it crashes into the ground or another obstacle.

DBL is another principle of stability/instability related to rear overturns. When a two-wheel-drive tractor is pulling a load, its rear tyres push against the ground. Simultaneously, the load attached to the tractor is pulling back and down against the forward movement of the tractor. The load is pulling down because it is resting on the earth’s surface. This backward and downward pull results in the rear tyres becoming a pivot point, with the load acting as a force trying to tip the tractor rearward. An “angle of pull” is created between the ground’s surface and the point of attachment on the tractor. The heavier the load, and the higher the angle of pull, the more leverage the load has to tip the tractor rearward.

Runovers

There are three basic types of tractor runover incidents. One is when a passenger (extra rider) on the tractor falls off the tractor. A second is when the tractor operator falls off the tractor. The third type occurs when a person already on the ground is run over by the tractor. The person already on the ground may be a bystander (e.g., a non-working adult or a small child), a co-worker or the tractor operator. The tractor runover event often involves trailing machinery hitched to the tractor; it may be the trailing machinery that inflicts the injury. Extra rider injury incidents occur because there is no safe location for an extra person on a tractor, yet the practice of taking extra riders is common, as a means of saving time, for convenience, work assistance or baby-sitting. Whether an extra rider can be justified for any reason is strictly in the eye of the beholder. Safety experts and tractor manufacturers strongly recommend against an operator carrying an extra rider for any reason. This advice, however, conflicts with several factors that farmers must face daily. For instance, it is human nature to want to complete work tasks as easily and quickly as possible; different transportation may call for added expenditure of a meagre money supply; other baby-sitting options simply may not exist; and new tractor drivers must be taught how to operate tractors.

Persons already on the ground, usually tractor operators or children, are occasionally run over by tractors and their attached equipment. Tractor operators sometimes try to start their tractor from the ground, instead of from the operator’s seat. Most of these incidents occur with older tractors that will start with the tractor in gear, or on newer tractors where the starting interlocks built into the tractor have been by-passed. Small children, usually under the age of five, are sometimes run over by tractors and machinery that is moved around the farmstead. Often, the tractor operator is unaware that the child is even near the equipment. A loud noise, such as the start-up of a tractor, is often attractive to young children and may draw them near. And the practice of allowing extra riders may bring them running to the tractor.

Tractor safety rules include:

  • The most important safety device for a tractor is a rollover protective structure (ROPS). This device, along with a properly buckled seat-belt, prevents an operator from being crushed by the tractor during a rollover.
  • A ROPS enclosed cab provides even more protection, as cabs also provide protection from adverse weather elements and from falling off the tractor.
  • A master shield over the PTO stub shaft protects against PTO entanglement.
  • The one seat–one rider rule and other safe operating practices must be followed.
  • Operator manuals must be read to learn how to safely operate the machine.
  • Workers must be physically, psychologically and physiologically capable of operating a given machine.

 

Machinery Hazards

There are a multitude of machines used in mechanized agriculture. These machines are powered in many different ways including PTO shafts, hydraulic oil pressure, electrical power, engine power and ground traction. Many machines have several types of hazards. Table 2 gives machine hazards, descriptions of the hazards and examples of where the hazards occur on various machines.

Table 2. Common machinery hazards and where they occur

Hazards

Sources

Locations

Pinch points

Two machine parts moving together with at least one of them moving in a circle

Where drive belts contact pulley wheels, drive chains contact gear sprockets, feed rolls mesh together

Wrap points

An exposed/unguarded rotating machine component

Power take-off (PTO) drive shafts, beater bars on self-unloading ensilage wagons, blades of some manure spreaders

Shear/cutting points

The edges of two moving parts move across one another, or a single edge moves against a stationary edge or soft material

Mowers and forage harvesters, small-grain combine heads, bedding choppers, grain augers

Crush points

Two moving objects moving toward each other, or one moving object moves toward a stationary object

The front and rear tires/sections of articulating tractors, hitching machinery, a hand caught under a piece of hydraulically-controlled equipment

Free-wheeling parts

Machine parts that continue to move after power to the part has stopped, usually from the continuing rotation of knife or fan blades

Forage harvesters, feed grinders, rotary mowers, ensilage blowers

Thrown objects

The chopping, grinding, cutting, and flinging motions of machines. Small objects such as rocks, metal, glass, sticks, and vegetation may be picked up and thrown with great force

Rotary mowers, feed grinders, combines with straw choppers, and manure spreaders

Stored energy

Energy that is confined and released unintentionally or unexpectedly

Machine springs, hydraulic systems, compressed air, electrical systems

Burn points

Skin burns from contacting hot parts of machines

Hot mufflers, engine blocks, pipes, fluids (fuel, oils, chemicals)

Pull-in points

Occurs at the point where the machine takes the crop material in for further processing

Corn pickers and combines, forage choppers, and hay balers

Noise-induced hearing loss

Operating machinery

Tractors, field machinery, grain augers, dryers, silo blowers, bedding choppers, feed grinders. Damaging noise level may come from a combination of one or more machines. Older machines generally produce louder sounds than newer machines.

 

Machinery power and speed

Though workers may understand that machinery is powerful and operates at very high speeds, most workers have not stopped to consider just how powerful machines are in comparison to their own power, nor do they fully comprehend how fast machines are. Machinery power varies considerably, but even small machines generate many times more horsepower than any person. A quick, pull-away action of a human arm normally generates less than 1 horsepower (hp), sometimes much less. A small 16-hp machine, such as a walk-behind mower, may have 20 to 40 times more power pulling a person into the machine than that person can generate pulling away. A medium-sized machine operated at 40 to 60 hp will have hundreds of times more power than a person.

This power and speed combination presents many potentially hazardous situations to workers. For example, the tractor’s PTO stub shaft transfers power between the tractor and PTO-powered machinery. Power transfer is accomplished by connecting a drive shaft from the machinery to the tractor’s PTO stub. The PTO stub and drive shaft rotate at 540 rpm (9 times/second) or 1,000 rpm (16.7 times/second) when operating at full recommended speed. Most incidents involving PTOs stem from clothing suddenly caught by an engaged but unguarded PTO stub or driveline. Even with a relatively quick reaction of 1 second (i.e., the worker tries to pull away from the shaft) and a shaft with a diameter of 76 mm operating only at half speed (e.g., at 270 rpm (one-half of 540), the victim’s clothing has already wrapped 1.1 m around the shaft. A faster-operating PTO and/or a slower reaction provides even less of an opportunity for the worker to avoid entanglement with the shaft.

When a machine is running at full recommended PTO speed, crop material moves into the machine intake or processing area at approximately 3.7 m/s. If a worker is holding onto crop material as it begins entry into the machine, he or she is usually unable to let go quickly enough to release the material before being pulled into the machine. In 0.3 second, the worker will be pulled 1.1 m into the machine. This situation most often happens when crop material plugs the intake point of the machine and the worker attempts to unplug it with the PTO engaged.

Machinery safety

Machinery safety is largely a matter of keeping the guards and shields that came with the original in place and properly maintained. Warning decals should be used as a reminder to keep guards and shields in place. If guards or shields must be removed for maintenance, service or adjustment, they must be replaced immediately upon completion of the repair. Safe operating practices must be followed. For example, the tractor must be shut off and the PTO or block hydraulic systems disengaged before unplugging or servicing equipment. Operator manuals must be read and their safety instructions followed. Workers must be properly trained.

 

Back

Thursday, 10 March 2011 14:51

Manual Operations in Farming

Agricultural methods and practices vary across national boundaries:

  • industrial agriculture—industrialized countries of the West (temperate climate) and specialized sectors of the tropical countries
  • green revolution agriculture—well endowed areas in the tropics, primarily irrigated plains and deltas of Asia, Latin America and North Africa
  • resource-poor agriculture—hinterlands, dry lands, forests, mountains and hills, near deserts and swamps. About 1 billion people in Asia, 300 million in sub-Saharan Africa and 100 million in Latin America are dependent on this form of agriculture. Women comprise a large proportion of subsistence farmers—nearly 80% of the food for sub-Saharan Africa, 50 to 60% of Asia’s food, 46% of the Caribbean’s food, 31% of North Africa and the Middle East’s food and 30% of Latin America’s food is produced by women (Dankelman and Davidson 1988).

 

With distinct agro-climatic features, the farm crops are grouped as follows:

  • Field crops (cereals, oilseeds, fibre, sugar and fodder crops) are rain-fed or cultivated through controlled irrigation.
  • Upland and semi-upland cultivation (wheat, groundnuts, cotton and so on) are practised where irrigation or rain water is not abundantly available.
  • Wetland cultivation (rice crops) is practised where the land is ploughed and puddled with 5 to 6 cm of standing water and seedlings are transplanted.
  • Horticulture crops are fruit, vegetable and flower crops.
  • Plantation or perennial crops include coconut, rubber, coffee, tea and so on.
  • Pastures are anything nature grows without human intervention.

 

Farming Operations, Hand Tools and Machinery

Farming in the tropical countries is labour intensive. The ratio of rural population to arable land in Asia is twice as great as in Africa and three times that of Latin America. It is estimated that human effort provides more than 70% of the energy required for crop production tasks (FAO 1987). Improvement in the existing tools, equipment and methods of work has significant effects in minimizing human strain and fatigue and increasing farm productivity. For field crops, farm activities may be categorized based on the physiological demand of work with reference to an individual’s maximal working capacity (see table 1).

Table 1. Categorization of farm activities

Work severity

Farm operations

 

Seed bed preparation

Sowing

Weeding and intercultivation

Harvesting

Light work

Laddering (two workers)

Broadcasting seeds/fertilizer, scaring birds, ridging

Fertilizer broadcasting

Grain cleaning, grading, spreading vegetables (squatting), pounding grain (helper), winnowing (sitting)

Moderately heavy work

Walking behind animal-drawn implement, levelling soil surface with wooden rake, laddering (one worker), digging soil with spade, bush cutting

Manual uprooting of seedlings (squatting and bent posture), transplanting seedlings (bent posture), walking on a puddled field

Manual weeding with sickle and hand hoe (squatting and bent posture), channel irrigation, knapsack spraying of pesticides, weeder operation in wet and dry soil

Cutting crops, harvesting paddy, wheat (squatting and bent posture), plucking vegetables, manual winnowing (sitting and standing), cutting sugarcane, pedal-thresher helper, carrying load (20-35 kg)

Heavy work

Ploughing, water lifting (swing busket), hoeing dry soil, bund trimming wet soil, spade work, disc harrowing

 

Weeder operation in dry soil

Grain threshing by beating, pounding grain

Extremely heavy work

Bund trimming dry soil

Germinating seeder operation in puddled field

 

Pedal threshing, carrying load on head or yoke (60-80 kg)

Source: Based on data from Nag, Sebastian and Marlankar 1980; Nag and Chatterjee 1981.

Seed-bed preparation

A suitable seed-bed is one that is mellow yet compact and free from vegetation that would interfere with seeding. Seed-bed preparation involves use of different types of hand tools, shallow chisel desi or a mould board plough pulled by draft animals (figure 1) or tractor implements for ploughing, harrowing and so on. About 0.4 hectare (ha) of land can be tilled by a bullock-drawn plough in a day, and a pair of bullocks can provide power to the extent of 1 horsepower (hp).

Figure 1. Bullock-drawn shallow chisel desi plough

AGR100F1

In using animal-drawn equipment, the worker acts as a controller of animals and guides the implement with a handle. In most cases, the operator walks behind the implement or sits on the equipment (e.g., disc harrows and puddlers). The operation of animal-drawn implements involves considerable human energy expenditure. For a 15 cm plough, a person may walk about 67 km to cover a 1-hectare area. At a walking speed of 1.5 km/h, the human energy expenditure amounts to 21 kJ/min (about 5.6 × 104 kJ per ha). A handle on implements that is too long or too short results in physical discomfort. Gite (1991) and Gite and Yadav (1990) suggested that the optimum handle height of an implement may be adjusted between 64 and 84 cm (1.0 to 1.2 times the metacarpal III height of the operator).

Hand tools (spade, shovel, hoe and so on) are used for digging and loosening the soil. To minimize drudgery in shovelling work, Freivalds (1984) deduced the optimum rate of work (i.e., shovelling rate) (18 to 21 scoops/minute), shovel load (5 to 7 kg for 15 to 20 scoops/minute, and 8 kg for 6 to 8 scoops/minute), throw distance (1.2 m) and throw height (1 to 1.3 m). Recommendations also include a shovel lift angle of about 32°, a long tool handle, a large, square-pointed blade for shovelling, a round-pointed blade for digging and hollow back construction to reduce shovel weight.

Nag and Pradhan (1992) suggested low-lift and high-lift hoeing tasks (see figure 2), based on physiological and biomechanical studies. As a general guide, the method of work and the hoe design are the deciding factors in performance efficiency of hoeing tasks (Pradhan et al. 1986). The mode of striking the blade to the ground determines the angle at which it penetrates the soil. For low-lift work, the work output was optimized at 53 strokes/ minute, with a land area dug of 1.34 m2/minute, and a work-rest ratio of 10:7. For high-lift work, the optimal conditions were 21 strokes per minute and 0.33 m2/minute of land dug. The shape of the blade—rectangular, trapezoidal, triangular or circular—depends upon the purpose and preference of the local users. For different modes of hoeing, the recommended design dimensions are: weight 2 kg, angle between blade and handle 65 to 70° , handle length 70 to 75 cm, blade length 25 to 30 cm, blade width 22 to 24 cm and handle diameter 3 to 4 cm.

Figure 2. Hoeing tasks in bund trimming in paddy field

AGR100F2

Pranab Kumar Nag

Sowing/planting and fertilizer application

The sowing of seeds and planting of seedlings involve the use of planters, seeders, drills and the manual broadcasting of seeds. About 8% of total person-hours are required for broadcasting of seeds and uprooting and transplanting of seedlings.

  • In the broadcasting of seeds/fertilizer by hand, manually operated broadcasters allow uniform distribution with minimum drudgery.
  • Seeding behind a plough consists of sowing of seeds in a furrow opened by a wooden plough.
  • In drilling, seeds are placed in the soil by a seed drill or seed-cum-fertilizer drill. The push/pull force required for a worker to operate the drill (manual or animal-drawn units mounted on wheels) is an important design consideration.
  • Dibbling is the placing of seeds by hand or with a small implement (a dibbler), at an average spacing of 15 x 15 cm or 25 x 25 cm. Abrasion of fingers and bodily discomfort due to bent and squat postures are common complaints.
  • In planting, sugar cane sets are planted at 30 cm length in a furrow; potato seed tubers are planted flat and ridges are made.
  • About 1/3 of the world’s rice is grown by the transplanting system. This is also done for tobacco and some vegetable crops. Usually, germinating seeds are broadcasted densely on a puddled field. The seedlings are uprooted and transplanted to a puddled field by hand or with manual or power-operated transplanters. The operator of a manually operated transplanter walks behind the unit to operate the handle mechanism to pick and transplant the seedlings.

For manual transplanting, the workers are required to be immersed knee deep in mud. The squatting posture used for planting on dry land, with one or two legs flexed at the knee, cannot be adopted in a watered field. About 85 person-hours are required to transplant seedlings for each hectare of land. The awkward posture and static load exert strain on the cardiovascular system and cause low-back pain (Nag and Dutt 1980). Manually operated seeders produce higher work output (i.e., a seeder is about eight times more efficient than transplanting by hand). However, maintaining the balance of the machine (see figure 3) in a puddled field requires about 2.5 times more energy than manual transplanting.

Figure 3. Operating an improved germinated seeder

AGR100F3

Paranab Kumar Nag

Plant protection

Fertilizer, pesticide, herbicide and other chemical applicators are operated by pressure through nozzles or by centrifugal force. Large-scale spraying is based on the hydraulic nozzle spray atomizer, either manually operated or using tractor-mounted equipment. Knapsack sprayers are scaled-down models of vehicle-mounted sprayers (Bull 1982).

  • A compression knapsack sprayer consists of a tank, a pump and a rod with nozzle and hose.
  • A lever-operated knapsack sprayer (10 to 20 l) has an operating lever.
  • A power knapsack sprayer consists of a chemical tank of about 10-litre capacity and an air-cooled engine of 1 to 3 hp. The sprayer and engine unit is mounted on a frame and carried on the operator’s back.
  • A hand-operated bucket sprayer and foot-operated sprayer require two persons for operating the pump and spraying. A rocking sprayer is operated by the rocking (forward and backward) movement of the handle lever.

 

When carried on the shoulder for prolonged periods, the vibrations of knapsack sprayers/chemical applicators have detrimental effects on the human body. Spraying using a knapsack sprayer results in potential skin exposure (the legs experience 61% of the total contamination, the hands 33%, the torso 3%, the head 2%, and the arms 1%) (Bonsall 1985). Personal protective clothing (including gloves and boots) can reduce the dermal contamination of pesticides (Forget 1991, 1992). The work is quite strenuous, due to carrying of the load on the back as well as continuous operation of the sprayer handle (20 to 30 strokes/minute); in addition, there is the thermoregulatory load due to protective garments. The weight and height of the sprayer, shape of sprayer tank, mounting system and force required to operate the pump are important ergonomic aspects.

Irrigation

Irrigation is a prerequisite for intensive cropping in arid and semi-arid regions. Since time immemorial, various indigenous devices have been used for lifting water. Lifting water by different manual methods is physically strenuous. In spite of the availability of water pump sets (electrical or engine powered), manually operated devices are widely used (e.g., swing baskets, counterpoise water lifts, water wheels, chain and washer pumps, reciprocating pumps).

  • A swing basket is used for lifting water from an irrigation channel (see figure 4). The capacity of the basket is about 4 to 6 l and the frequency of operation is about 15 to 20 swings/minute. Two operators work at right angles to the direction of basket motion. The work demands heavy physical activity, with adoption of awkward body movements and posture.
  • A counterpoise water lift consists of a container attached to the end of a horizontal lever which is supported on a vertical pole. The worker exerts force on the counterweight to operate the device.
  • Reciprocating pumps (piston-cylinder type hand pumps) are operated either by hand in reciprocating mode or by pedalling in rotary mode.

 

Figure 4.  Lifting water from irrigation channel using a swing basket

AGR100F4

Pranab Kumar Nag

Weeding and intercultivation

Undesirable plants and weeds cause losses by impairing crop yields and quality, harbouring plant pests and increasing irrigation cost. Reduction in yield varies from 10 to 60% depending upon the thickness of growth and the kind of weeds. About 15% of human labour is spent in removing weeds during the cultivating season. Women typically comprise a large portion of the workforce engaged in weeding. In a typical situation, a worker spends about 190 to 220 hours weeding one hectare of land by hand or hand hoe. Spades are also used for weeding and intercultivation.

Of several methods (e.g., mechanical, chemical, biological, cultural), mechanical weeding, either by pulling out the weeds by hand or with hand tools like the hand hoe and simple weeders, is useful in both dry and wet land (Nag and Dutt 1979; Gite and Yadav 1990). In dry land, the workers squat on the ground with one or two legs flexed at the knee and remove weeds using a sickle or hand hoe. In watered land, the workers adopt a bent forward stooping posture to remove weeds manually or with the help of weeders.

The physiological demand in using weeders (e.g., blade and rake, projection finger, double sweep type weeders) is relatively higher than in manual weeding. However, the efficiency of work in terms of area covered is significantly better with the weeders than with manual weeding. The energy demand in manual weeding jobs is only about 27% of one’s working capacity, whereas for different weeders, the energy demand goes up to 56%. However, the strain is relatively less in the case of wheel hoe-type weeders, with which it takes about 110 to 140 person-hours to cover one hectare. A wheel hoe-type weeder (push/pull) consists of one or two wheels, a blade, a frame and a handle. A force (push or pull) of about 5 to 20 kilograms of force (1 kgf = 9.81 Newtons) is required, with a frequency of about 20 to 40 strokes per minute. The technical specifications of the wheel hoe-type weeders, however, need to be standardized for better operation.

Harvesting

In rice and wheat crops, harvesting requires 8 to 10% of the total person-hours used in crop production. Despite rapid mechanization in harvesting, large-scale dependence on manual methods (see figure 5) will continue for years to come. Hand tools (sickle, scythe and so on) are used in manual harvesting. The scythe is commonly used in some parts of the world, because of its large area of coverage. However, it requires more energy than harvesting with a sickle.

Figure 5. Harvesting wheat crop using a sickle

AGR100F5

Pranab Kumar Nag

The popularity of the sickle is due to its simplicity in construction and operation. A sickle is a curved blade, with a smooth or serrated edge, attached to a wooden handle. Sickle design varies from region to region, and there is a difference in cardiorespiratory load with different types of sickles. The output varies from 110 to 165 m2/hour, values corresponding to 90 and 60 person-hours per hectare of land. Awkward work postures may lead to long-term clinical complications relating to the back and to the joints of the limbs. Harvesting in a bent posture has the advantage of mobility on both dry and wet land, and it is about 16% faster than squatting; however, a bent posture is 18% more energy demanding than squatting (Nag et al. 1988).

Harvesting accidents, lacerations and incised wounds are common in paddy, wheat and cane sugar fields. The hand tools are primarily designed for right-handed persons, but are often used by left-handed users, who are unaware of the possible safety implications. The important factors in a sickle design are the blade geometry, blade serration, handle shape and size. Based on an ergonomics study, suggested design dimensions of a sickle are: weight, 200 g; total length, 33 cm; handle length, 11 cm; handle diameter, 3 cm; radius of blade curvature, 15 cm; blade concavity, 5 cm. For a serrated sickle: tooth pitch, 0.2 cm; tooth angle, 60°; and ratio of the length of cutting surface to chord length, 1.2. Since the workers perform activities under extreme climatic conditions, health and safety issues are critically important in tropical farming. The cardiorespiratory strain accumulates over long hours of work. Extreme climatic conditions and heat disorders place added stress on the worker and diminish working capacity.

Harvesting machines include mowers, choppers, balers and so on. Power-operated or animal-drawn reapers are also used for harvesting field crops. Combine harvesters (self-propelled or tractor operated) are useful where intensive cultivation is practised and the labour shortage is acute.

Harvesting of sorghum is done by cutting the ear-head and then cutting the plant, or vice versa. The cotton crop is collected in 3 to 5 pickings by hand as the ball matures. Harvesting of potatoes and sugar beets is done manually (see figure 6) or by using a blade harrow or digger, which may be animal or tractor powered. In the case of groundnuts, the vines are either pulled manually or removed using diggers, and the pods separated.

Figure 6.  Manual harvesting of potatoes with a hand hoe

AGR100F6

Threshing

Threshing includes separation of grains from the earheads. Age-old manual methods of threshing of grain from the paddy pinnacle are: rubbing the earheads with one’s feet, beating of the harvested crop on a plank, animal treading and so on. Threshing is classified as a moderately heavy task (Nag and Dutt 1980). In manual threshing by beating, (see figure 7) one separates about 1.6 to 1.8 kg of grain and 1.8 to 2.1 kg of straw per minute from medium sized paddy/wheat plants.

Figure 7. Threshing paddy pinnacle by beating

AGR100F7

Pranab Kumar Nag

Mechanical threshers carry out threshing and winnowing operations simultaneously. The pedal thresher (oscillating or rotary mode) increases the output to 2.3 to 2.6 kg of grain (paddy/wheat) and 3.1 to 3.6 kg of straw per min. Pedal threshing (see figure 8) is a more strenuous activity than manual threshing by beating. The pedalling and holding of paddy plants on the rolling drum result in high muscular strains. Ergonomic improvements in the pedal thresher may allow a rhythmic pattern of leg work in alternate sitting and standing postures and minimize postural strains. The optimal momentum of the thresher may be reached at about 8 kg weight of the rolling drum.

Figure 8. A pedal thresher in operation

AGR100F8

Pranab Krumar Nag

Power threshers are gradually being introduced in green revolution areas. Essentially they consist of a prime mover, a threshing unit, a winnowing unit, a feeding unit and a outlet for clean grain. Self-propelled combines are a combination of a harvester and a thresher unit for grain crops.

Fatal accidents have been reported in grain threshing using power threshers and fodder cutters. The incidence of moderate to severe thresher injuries was 13.1 per thousand threshers (Mohan and Patel 1992). Hands and feet can be injured by the rotor. The position of the feeding chute can result in awkward postures when feeding the crop into the thresher. The belt powering the thresher is also a common cause of injuries. With fodder cutters, the operators can sustain injury while feeding the fodder into the moving blades. Children sustain injury when playing with the machines.

The workers often stand on unstable platforms. In the event of a jerk or loss of balance, the torso weight pushes the hands into the threshing drum/fodder cutter. The thresher must be designed so that the feeding chute is at elbow level and the operators stand on a stable platform. The design of the fodder cutter may be improved for safety as follows (Mohan and Patel 1992):

  • a warning roller placed on the chute before the feed rollers
  • a locking pin to fix the flywheel when the cutter is not in use
  • gear cover and blade guards to push limbs away and prevent clothes from getting entangled.

 

For threshing groundnuts, the traditional practice is to hold the plants by one hand and strike them against a rod or grill. For threshing maize, tubular maize shellers are used. The worker holds the equipment in his or her palm and inserts and rotates cobs through the equipment to separate the maize grains from the cobs. Output with this equipment is about 25 kg/hour. Hand-operated rotary type maize shellers have higher work output, about 50 to 120 kg/hour. The length of the handle, the force required to operate it and the speed of operation are the important considerations in hand-operated rotary maize shellers.

Winnowing

Winnowing is a process to separate grains from chaff by blowing air, using a hand fan or a pedal- or motor-driven fan. In manual methods (see figure 9), the whole content is thrown up in the air, and the grain and chaff get separated out by differential momentum. A mechanical winnower may, with considerable human exertion, be hand or pedal operated.

Figure 9. Manual winnowing

AGR100F9

Pranab Kumar Nag

Other post-harvest operations include cleaning and grading of grains, shelling, decortication, hulling, peeling, slicing, fibre extraction and so on. Different types of manually operated equipment are used in post-harvest operations (e.g., potato peelers and slicers, coconut dehuskers). Decortication involves breaking of shells and removal of seeds (e.g., groundnuts, castor beans). A groundnut decorticator separates kernels from pods. Manual decortication has a very low output (about 2 kg of pod shelling per person-hour). Workers complain of bodily discomfort due to the continuous sitting or squatting posture. Oscillating or rotary-mode decorticators have an output of about 40 to 60 kg of pods per hour. Shelling and hulling refer to separation of seed coat or husk from the inner portion of the grain (e.g., paddy, soybean). Traditional rice hullers are manually (hand or foot) operated and are widely used in rural Asia. The maximum force which can be exerted by hand or foot determines the size and other characteristics of the device. Nowadays, motorized rice mills are used for hulling. In some grains, such as pigeonpea, the seed coat or husk is tightly attached. Removal of the husk in such cases is called dehusking.

For different hand tools and manually operated implements, the grip size and the force exerted on the handles are important considerations. In the case of shears, the force which can be applied by two hands is important. Although most injuries related to hand tools are classified as minor, their consequences are often painful and disabling because of delayed treatment. Design changes in hand tools should be limited to those that can be easily fabricated by village artisans. Safety aspects need to be given due consideration in powered equipment. Safety shoes and gloves available at present are far too expensive and are not suitable for farmers in the tropics.

Manual material-handling tasks

Most agricultural activities involve manual material-handling tasks (e.g., lifting, lowering, pulling, pushing and carrying of heavy loads), resulting in musculoskeletal strains, falls, spinal injuries and so on. The fall injury rate increases dramatically when the fall height is more than 2 m; impact forces are reduced manyfold if the victim falls on soft earth, hay or sand.

In rural areas, loads weighing 50 to 100 kg might be carried several miles on a daily basis (Sen and Nag 1975). In some countries, women and children have to fetch water in large quantities from a distance. These arduous tasks need to be minimized to the extent possible. Different methods of water carriage involve carrying on the head, on the hip, on the back and on the shoulder. These have been associated with a variety of biomechanical effects and spinal disorders (Dufaut 1988). Attempts have been made to improve shoulder load-carrying techniques, designs of wheelbarrows and so on. Load transportation using transverse yoke and head load are more efficient than the frontal yoke. The load optimization that can be carried by men may be obtained from the nomogram shown (figure 10). The nomogram is based on a multiple regression drawn between oxygen demand (the independent variable) and load carried and walking speed (the dependent variables). One may put a scale on the graph across the variables to identify the result. Two variables must be known to find the third. For example, with an oxygen demand of 1.4 l/min (approximate equivalent of 50% of one’s maximum working capacity) and walking speed of 30 m/min, the optimum load would be about 65 kg.

Figure 10. A nomogram to optimize load to be carried on head/yoke, with reference to walking speed and oxygen demand of work.

AG100F10

In view of the diversity of farm activities, certain organizational measures towards redesigning of tools and machinery, methods of work, installation of safety guards on machinery, optimization of human exposure to adverse work environment and so on may significantly improve conditions of work for farming populations (Christiani 1990). Extensive ergonomic research on farm methods and practices, tools and equipment may generate a great deal of knowledge for the betterment of health, safety and productivity of billions of agricultural workers. This being the world’s largest industry, the primitive image of the sector, particularly the resource-poor tropical agriculture, could be transformed as task-oriented. Thus rural workers can undergo systematic training on the hazards of jobs, and safe operational procedures can be developed.

 

Back

Thursday, 10 March 2011 14:49

Storing and Transportation Operations

Storing

The growing and gathering of crops and production of livestock has long been recognized as one of the world’s oldest and most important occupations. Farming and ranching today is as diverse as the many crops, fibres and livestock which are produced. At one extreme, the farming unit may consist of a single family that cultivates the soil and plants and harvests the crop, all by hand over a limited area. The opposite extreme includes large corporate farms spanning vast areas that are highly mechanized, using sophisticated machinery, equipment and facilities. The same is true for the storage of food and fibre. Storage of agricultural products may be as rudimentary as simple huts and hand-dug pits, and as complex as towering silos, bunkers, bins and refrigerated units.

Hazards and their prevention

Agricultural products such as grains, hays, fruit, nuts, vegetables and plant fibre are often stored for later human and livestock consumption or sale to the general populace or to manufacturers. The storage of agricultural products prior to shipment to market may occur in a variety of structures—pits, bunkers, bins, silos, refrigerated units, carts, wagons, barns and railroad cars, to mention a few. Despite the diversity of products being stored and of storage facilities, there are hazards which are common to the storage process:

Falls and falling objects

Falls may occur from heights or at the same level. In the case of bins, silos, barns and other storage structures, falls from heights most often occur from and in storage structures. Most often the cause is unguarded roofs, floor openings, stairways, lofts and shafts, and climbing ladders or standing on raised work areas such as an unprotected platform. Falls from height may also result from climbing on or off the transportation unit (e.g., wagons, carts and tractors). Falls from the same level occur from slippery surfaces, tripping over objects or being pushed by a moving object. Protection against falls includes such measures as:

  • provision of safety belts, harnesses, lifelines and safety boots
  • installation of guard rails, toeboards, cat-ladders or crawling boards on sloped roofs
  • guarded floor openings, lofts and shafts
  • use of the standard rise and run of stairways, provision of handrails on both sides, and application non-skid strips where necessary
  • maintaining floors in good condition, free from uneven surfaces, holes and accumulations of waste or slippery substances
  • provision of handholds on permanent ladders, guard platforms and landings
  • maintaining extension or step ladders in good condition and training employees on their use.

 

Agricultural products may be stored loose in a facility or bundled, bagged, crated or bailed. Loose storage is often associated with grains such as wheat, corn or soybeans. Bundled, bagged, crated or bailed products include hay, straw, vegetables, grains and feeds. Falls of materials occur in all types of storage. Collapse of unsecured stacked foodstuffs, overhead materials and piles of goods are often causes of injury. Employees should be trained in the correct stacking of goods to prevent their collapse. Employers and managers must monitor the workplace for compliance.

Confined spaces

Agricultural products may be stored in two types of facilities—those that contain enough oxygen to sustain life, such as barns, open carts and wagons, and those that do not, such as some silos, tanks and refrigeration units. The latter are confined spaces, and should be treated with appropriate precautions. The oxygen level should be monitored prior to entry and a supplied air or self-contained breathing unit used if necessary; someone else should be on hand. Suffocation may also occur in either type of facility if the goods which it contains have the characteristics of a fluid. This is commonly associated with grains and similar foodstuffs. The worker dies as a result of drowning. In grain bins it is a common practice for an agricultural worker to enter the bin due to difficulties in loading or unloading, often caused by a condition of the grain resulting in bridging. Workers attempting to alleviate the situation by unbridging the grain may voluntarily walk on the bridged grain. They may fall in and be covered with the grain or be sucked under if the loading or unloading equipment is operational. Bridging also may occur to the sides of such structures, in which case a worker may enter to knock down the material sticking to the sides and become engulfed when the material fails. A lockout/tagout system and fall protection such as a safety belt and rope are essential if workers are to enter this type of structure. Children’s safety is of special concern. Often inquisitive, playful and wanting to do adult chores, they are attracted to such structures, and the results are all-too-often fatal.

Fruit and vegetables are often kept in cold storage prior to shipping to market. As indicated in the above paragraph, depending on the type of unit, cold storage may be considered a confined space and should be monitored for oxygen content. Other hazards include frostbite and cold-induced injury or death from body temperature loss following prolonged exposure to cold. Personal protective clothing should be worn appropriate to the temperature within the cold-storage unit.

Gases and poisons

Depending on the moisture content of the product when it is placed in storage and atmospheric and other conditions, feeds, grains and fibres may produce dangerous gases. Such gases include carbon monoxide (CO), carbon dioxide (CO2) and oxides of nitrogen (NOx), some of which may cause death in a matter of minutes. This is also especially important if the goods are stored in a facility in which nonlethal gases may be allowed to accumulate to dangerous levels, displacing oxygen. If the potential for gas production exists, then monitoring for gases should be done. In addition, foods and feeds may have been sprayed or treated with a pesticide during the growing period to kill weeds, insects or disease, or during the storage process to reduce spoilage or mould, spore or insect damage. This may add to the hazards of gas production, inhalation of dusts and handling of the product. Special care should be taken by workers to wear PPE depending on the nature and longevity of the treatment, the product used and the label directions.

Machine hazards

Storage facilities may contain a variety of machinery for conveying the product. These range from belt and roller conveyors to blowers, augers, slides and other such product-handling devices, each with its own power source. Hazards and suitable precautions include:

  • Nip points formed by belts, pulleys and gears. Agricultural workers should be protected from nip and shear points by an appropriate guarding around the point of potential contact.
  • Protruding belt fasteners, setscrews, keys, bolts and grooves. Protruding setscrews, keys or bolts on revolving shafts should be countersunk, encased or shrouded. Belt fasteners should be inspected and repaired.
  • Shear points caused by flywheel arms, augers and their housing, pulley spokes, crank and lever mechanisms. These should be guarded or enclosed.
  • Contact with moving transmission or electrical elements. These should be guarded or enclosed.
  • Inadvertent starting of machinery or equipment. A system for locking out or tagging out equipment prior to maintenance or repair should be implemented and enforced.
  • Loose clothing or hair getting wound on or caught by shafts. Clothing that is loose, frayed or that has hanging threads should never be worn. Other personal protective apparel and shoes appropriate to the job task should be worn.
  • Excessive noise. Noise exposure should be monitored and administrative, engineering and/or personal protective controls should be taken if necessary.

 

Employees should be trained and aware of the hazards, basic safety rules and safe working methods.

Health outcomes

Agricultural workers who are involved in the handling of agricultural products for storage are at risk for respiratory disorders. Exposures to a variety of dusts, gases, chemicals, silica, fungal spores and endotoxins can result in damage to the lungs. Recent studies link lung disorders caused by these substances to workers who handle grain, cotton, flax, hemp, hay and tobacco. Therefore the populations at risk are worldwide. Agricultural lung disorders have many common names, some of which include: occupational asthma, farmer’s lung, green tobacco sickness, brown lung, organic dust toxic syndrome, silo filler’s or unloader’s disease, bronchitis and airway obstruction. Symptoms may first manifest themselves as being characteristic of influenza (chills, fever, coughing, headaches, myalgias and breathing difficulty). This is especially true for organic dusts. Prevention of lung dysfunction should include an assessment of the worker’s environment, health promotion programmes targeted at primary prevention and the use of personal protective respirators and other protective devices based on the environmental assessment.

Transportation Operations

Although it may seem simple, the transportation of goods to market is often as complex and hazardous as growing and storing the crop. The transportation of products to market is as diversified as the types of farming operations. Transportation may range from goods being carried by humans and livestock, to being transported by simple mechanical devices such as bicycles and animal-drawn carts, being hauled by complex mechanical equipment such as large carts and wagons pulled by tractors, to the use of commercial transportation systems, which include large trucks, buses, trains and airplanes. As the world’s population increases and urban areas grow, road travel of agricultural equipment and implements of husbandry has increased. In the US, according to the National Safety Council (NSC), 8,000 farm tractors and other agricultural vehicles were involved in highway accidents in 1992 (NSC 1993). Many farming operations are consolidating and expanding by acquiring or renting a number of smaller farms which are typically scattered and not adjoining. A 1991 study in Ohio showed that 79% of the farms surveyed operated in multiple locations (Bean and Lawrence 1992).

Hazards and their prevention

Although each of the modes of transportation mentioned above will have its own unique hazards, it is the intermix of civilian traffic with agricultural transport machinery and equipment that is of major concern. The increase in road travel of agricultural equipment has resulted in a greater number of collisions between motor vehicles and slower moving agricultural equipment. Farm equipment and implements of husbandry may be wider than the width of the road. Due to pressure of planting at the right time to assure a crop or harvesting and getting the crop to a market or storage location as quickly as possible, agricultural machinery must often travel on the roadways during periods of darkness, early morning or evening.

An in-depth study of all 50 states’ codes in the United States revealed that the lighting and marking requirements vary greatly from state to state. This diversity in requirements does not communicate a consistent message to motor vehicle drivers (Eicher 1993). Faster speeds of other vehicles combined with inadequate lighting or marking of agricultural equipment is often a deadly combination. A recent study in the United States found that the common accident types are rear end, sideswipe-meeting, sideswipe-passing, angle, head-on, backing and other. In 20% of the 803 two-vehicle crashes studied, the farm vehicle was struck from an angle. In 28% of the crashes, the farm vehicle was sideswiped (15% meeting and 13% passing). Twenty-two per cent of the accidents consisted of rear-end (15%), head-on (4%) and backing (3%) collisions. The remaining 25% were crashes which were caused by something other than a moving vehicle (i.e., a parked vehicle, pedestrian, animal and so on) (Glascock et al. 1993).

Livestock are used in many parts of the world as the “horsepower” to transport agricultural products. Although beasts of burden are generally reliable, most are colourblind, have territorial and maternal instincts, react independently and unexpectedly, and are of great strength. Such animals have caused vehicle crashes. Falls from agricultural machinery and implements of husbandry are common.

The following general safety principles apply to transportation operations:

  • Local traffic rules, regulations or laws should be learned and obeyed.
  • No riders or passengers other than those that are necessary to accomplish the transport and unloading duties should be permitted.
  • Vehicles should stay as close to the shoulder of the road as road conditions will allow.
  • Passing other vehicles (moving or parked) and pedestrians must be done with caution.
  • Broken-down vehicles should be moved off the road if possible.
  • All marking and lighting on machinery and equipment should be maintained and clean.
  • Driving should never be done under the influence of alcohol or drugs.

 

Laws and regulations may dictate the state of acceptable lighting and marking. However, many such regulations only describe the minimal acceptable standards. Unless such regulations specifically prohibit retrofitting and adding additional lighting and marking, farmers should consider adding such devices. It is important that such lighting and marking devices be installed not only on self-propelled implements but also on pieces of equipment that they may be pulling or trailing.

Lights are especially critical for dusk, dawn and night-time movement of agricultural equipment. If the agricultural vehicle has a power source, consideration should be given to having, at a minimum: two headlights, two tail-lights, two turn signals and two brake lights.

Tail-lights, turn signals and brake lights may be incorporated into single units or can be attached as separate entities. Standards for such devices may be found through standard-setting organizations such as the American Society of Agricultural Engineers (ASAE), the American National Standards Institute (ANSI), the European Committee for Standardization (CEN) and the International Organization for Standardization (ISO).

If the agricultural vehicle does not have a power source, battery-powered lights, although not as effective, may be used. Many such lights are commercially available in a variety of types (flood, blinking, rotating and strobe) and sizes. If it is impossible to obtain these devices, then reflectors, flags and other alternative materials discussed below may be used.

Many new retroreflective fluorescent materials are available today to aid in marking agricultural vehicles for enhanced visibility. They are manufactured in patches or strips in a variety of colours. Local regulations should be consulted for acceptable colours or colour combinations.

Fluorescent materials provide excellent daytime visibility by relying on solar radiation for their light-emitting properties. A complex photochemical reaction takes place when the fluorescent pigments absorb non-visible solar radiation and re-emit the energy as a longer wavelength of light. In a sense, fluorescent materials appear to “glow” in the daytime and appear brighter than the conventional colours in the same light conditions. The primary disadvantage of fluorescent materials is their deterioration with prolonged exposure to solar radiation.

Reflection is an element of sight. Wavelengths of light strike an object and are either absorbed or bounced back in all directions (diffused reflection) or at an angle exactly opposite to the angle at which the light struck the object (specular reflection). Retroreflectivity is very similar to specular reflection; however, the light is reflected directly back toward the light source. There are three primary forms of retroreflective materials, each having a different degree of retroreflectivity based on how they were manufactured. They are presented here in increasing order of retroreflectivity: enclosed lens (often called engineering grade or Type ID), encapsulated lens (high intensity) and cube corner (diamond grade, prismatic, DOT C2 or Type IIIB). These retroreflective materials are excellent for night-time visual identification. These materials are also of great assistance in defining the extremities of agricultural implements. In this application, strips of retroreflective and fluorescent material across the width of the machinery, front and back, best communicate to drivers of other, nonagricultural vehicles the actual width of the equipment.

The distinctive red triangle with a yellow-orange centre is used in the United States, Canada and many other parts of the world to designate a class of vehicles as “slow moving”. This means the vehicle travels less than 40 km per hour on the roadway. Typically, other vehicles travel much faster, and the difference in speed may result in a misjudgement on the part of the faster vehicle driver, affecting the driver’s ability to stop in time to avoid an accident. This emblem or an acceptable substitute should always be used.

Health outcomes

Agricultural workers who are involved in the transportation of agricultural products may be at risk for respiratory disorders. Exposures to a variety of dusts, chemicals, silica, fungal spores and endotoxins may result in damage to the lungs. This is somewhat dependent on whether the transport vehicle has an enclosed cab and whether the operator engages in the loading and unloading process. If the transport vehicle has been used in the process of pesticide application, pesticides could be present and trapped inside the cab unless it has an air filtration system. Nevertheless, symptoms may first manifest themselves as being characteristic of influenza. This is especially true for organic dusts. Prevention of lung dysfunction should include an assessment of the worker’s environment, health promotion programmes targeted at primary prevention and the use of personal protective masks, respirators and other protective devices.

 

Back

Thursday, 10 March 2011 14:48

Harvesting Operations

The gathering in of agricultural crops upon maturity, or the practice of harvesting, signals the end of the production cycle prior to storage and processing. The size and quality of the crop removed from the field, orchard or vineyard represents the most significant measure of a farmer’s productivity and success. The value that has been placed on the outcome of the harvest is reflected in the terms used almost universally to measure and compare agricultural productivity, such as kilograms per hectare (kg/ha), bales per hectare, bushels per acre (bu/a) and tons per acre or hectare. From an agronomic perspective, it is actually the inputs that determine the yield; however, it is the harvest that becomes the primary determinant of whether or not there will be sufficient seed and resources to ensure the sustainability of the farm and those it supports. Because of the significance of harvest and all of its related activities, this part of the agricultural cycle has taken on an almost spiritual role in the lives of farmers throughout the world.

Few agricultural practices illustrate more clearly the scope and diversity of technology- and work-related hazards found in agricultural production than harvesting. Crop harvesting is carried out under a wide variety of conditions, over various types of terrain, utilizing machines from simple to complex that must handle a diversity of crops; it involves considerable physical effort from the farmer (Snyder and Bobick 1995). For these reasons, any attempt to briefly generalize the characteristics or nature of harvest practices and harvest-related hazards is extremely difficult. Small grains (rice, wheat, barley, oats and so on), for example, which dominate much of the planted cropland in the world, represent not only some of the most highly mechanized crops, but in large regions of Africa and Asia are harvested in a manner that would be familiar to farmers 2,500 years ago. The use of hand sickles to harvest a few stalks at a time, hard-packed clay threshing floors and simple threshing devices remain the primary tools of harvest for far too many producers.

The primary hazards associated with the more labour-intensive harvesting practices have changed little with time and are often overshadowed by the perceived increased risks associated with greater mechanization. Long hours of exposure to the elements, the physical demands resulting from lifting heavy loads, repetitive motion and awkward or stooped posture, along with natural hazards such as poisonous insects and snakes, have historically taken, and continue to take, a significant toll (see figure 1). Harvesting grain or sugar cane with a sickle or machete, picking fruit or vegetables by hand and manually removing peanuts from the vine are dirty, uncomfortable and exhausting tasks that in many communities frequently are completed by large numbers of children and women. One of the strongest motivating forces that has shaped modern harvesting practices has been the desire to remove the physical drudgery associated with manual harvesting.

Figure 1. Hand-harvesting millet

AGR070F6

Even if the resources were available to mechanize harvesting and reduce its risks (and for many small farmers in many areas of the world, they are not), investments to improve the safety and health aspects of harvesting would likely have smaller returns than would comparable investments to improve housing, water quality or health care. This is especially true if farmers have access to large numbers of unemployed or underemployed workers. High levels of unemployment and limited job opportunities, for example, place large numbers of younger workers at risk of injury during harvest because they are cheaper to use than machines. Even in many countries with highly mechanized agricultural practices, child labour laws frequently exempt children involved in agricultural activities. For example, special provisions of the US Department of Labor child labour laws continue to exempt children under 16 during harvest and allow them to operate agricultural equipment under certain conditions (DOL 1968).

Contrary to a general perception that greater mechanization in agriculture has increased the risks associated with agricultural production, with respect to harvesting, nothing could be further from the truth. Through the introduction of intensive mechanization in major grain- and forage-producing regions, the amount of time required to produce a bushel of grain, for example, has dropped from over an hour to under a minute (Griffin 1973). This accomplishment, though heavily dependent upon fossil fuels, has released tens of millions of people from the drudgery and unsafe working conditions associated with hand harvesting. Mechanization has resulted in not only tremendous increases in productivity and yields, but also the near elimination of the most historically significant harvest-related injuries, such as those involving livestock.

The intensive mechanization of the harvesting process, however, has introduced new hazards, which have required periods of adjustment and in some cases the replacement of machines with improved practices and designs that were either more productive or less hazardous. An example of this technological evolution was experienced with the transition that took place in corn harvesting in North America between the 1930s and 1970s. Up through the 1930s, the corn crop was almost entirely harvested by hand and transported to on-farm storage sites by horse-drawn wagons. The primary cause of harvest-related injuries was related to working with horses (NSC 1942). With the introduction and widespread use of the mechanical, tractor-drawn corn picker in the 1940s, horse- and livestock-related deaths and injuries rapidly declined during the harvest period, and there was a corresponding growth in the number of corn picker-related injuries. This was not because corn pickers were inherently more dangerous, but because the injuries reflected a rapid transition to a new practice that had not been fully refined and that farmers were unfamiliar with. As farmers adjusted to the technology and manufacturers improved the performance of the corn picker, and as more uniform varieties of corn were planted that were better suited to machine harvesting, the number of deaths and injuries quickly declined. In other words, the introduction of the corn picker ultimately resulted in a decline in harvest- related injuries due to exposure to traditional hazards.

With the introduction in the 1960s of the self-propelled combine, which could harvest higher-yielding corn varieties at rates ten or more times faster than the corn picker, corn picker injuries almost disappeared. But, once again, as with the corn picker, the combine introduced a new set of hazards that required a period of adjustment. For example, the ability to gather, cut, separate and clean the grain in the field using one machine changed the handling of grain from a lumpy flow process in the form of ear corn to shelled corn, which was almost fluid-like. Consequently, in the 1970s, there was a dramatic increase in the number of auger-related injuries, and of engulfments and suffocations in flowing grain that took place in storage structures and grain transport vehicles (Kelley 1996). In addition, there were new categories of injuries being reported that were related to the sheer size and weight of the combine, such as falls from the operator platform and ladders, which can place the operator as much as 4 m off the ground, and operators being crushed beneath the multi-row gathering unit.

The mechanization of the corn harvest directly contributed to one of the most dramatic shifts in rural population ever experienced in North America. The farm population, in less than 75 years after the introduction of hybrid varieties of corn and the mechanical corn picker, went from over 50% to less than 5% of the total population. Through this period of increased productivity and greatly reduced labour demands, the overall exposure to agricultural workplace hazards was substantially reduced, contributing to a drop in reported farm-related deaths from over 14,000 in 1942 to fewer than 900 in 1995 (NSC 1995).

Injuries associated with modern harvesting operations typically relate to tractors, machinery, grain-handling equipment and grain-storage structures. Since the 1950s, tractors have contributed to approximately one-half of all farm-related fatalities, with overturns being the single most important contributing factor. The utilization of rollover protective structures (ROPS) has proven to be the single most important intervention strategy in reducing the number of tractor-related fatalities (Deere & Co. 1994). Other design features that improved the safety and health of tractor operators included wider wheel bases and designs that lowered the centre of gravity to improve stability, all-weather operator enclosures to reduce exposure to the elements and dust, ergonomically designed seating and controls and reduced noise levels.

The problem of tractor-related injuries, however, remains significant and is a growing concern in areas that are being rapidly mechanized, such as China and India. In many areas of the world it is more likely to see the tractor being used as a vehicle of highway transport or a stationary power source than being used in the field to produce crops, as it was designed to do. In these areas, tractors are typically introduced with minimal operator training and are used widely as a means of transporting multiple passengers, another use for which the tractor was not designed. The result has been that runovers of extra riders who have fallen from the tractors during operation has become the second leading cause of tractor-related fatalities. If the trend towards greater utilization of ROPS continues, runovers may eventually become the leading cause of tractor-related fatalities worldwide.

Though used fewer hours during the year than tractors, harvesting equipment such as combines are involved in about twice as many injuries per 1,000 machines (Etherton et al. 1991). These injuries often take place during servicing, repairing or adjusting the machine when the power to machine components is still engaged (NSC 1986). Recent design changes have been made to incorporate more passive and active operator warnings and interlocks, such as safety switches in the operator seat to prevent machine operation when no one is in the seat, and to reduce the number of maintenance points to reduce operator exposure to operating machinery. Many of these design concepts, however, remain voluntary, are frequently by-passed by the operator and are not universally found on all harvesting machines.

Hay and forage harvesting equipment exposes workers to hazards similar to those found on combines. This equipment contains components that cut, crush, grind, chop and blow crop material at high speed, leaving little room for human error. As with grain harvesting, hay and forage harvesting must take place in a timely fashion in order to prevent damage to the crop from the elements. This added stress to complete tasks rapidly, in conjunction with machine hazards, frequently leads to injuries (Murphy and Williams 1983).

Traditionally, the hay baler has been identified as a frequent source of serious injuries. These machines are used under some of the most harsh conditions found in any type of harvesting. High temperature, rough terrain, dusty conditions and the need for frequent adjustments contribute to a high rate of injury. The conversion to large packages or bales of hay and mechanical handling systems has improved safety with a few exceptions, as was the case with the introduction of the early designs of the round baler. The aggressive compression rolls on the front of these machines resulted in a large number of hand and arm amputations. This design was later replaced with a less aggressive gathering unit, which nearly eliminated the problem.

Fire is a potential problem for many types of harvesting operations. Crops that are required to be dried to less than 15% moisture content for proper storage make excellent fuel if ignited. Combines and cotton harvesters are especially vulnerable to fires during field operation. Design features such as the use of diesel engines and protected electrical systems, proper equipment maintenance and operator access to fire extinguishers have been shown to reduce the risk of fire-related damage or injury (Shutske et al. 1991).

Noise and dust are two other hazards that are typically intrinsic to harvesting operations. Both pose serious long-term health risks to the operator of harvesting equipment. The inclusion of environmentally controlled operator enclosures in the design of modern harvesting equipment has done much to reduce operator exposure to excessive noise pressures and dust levels. However, most farmers have yet to benefit from this safety feature. The use of PPE such as ear plugs and disposable dust masks provides an alternative, but less effective, means of protection from these hazards.

As harvesting operations around the world become increasingly mechanized, there will be a continuing shift from environmental-, animal- and hand tool-related injuries to those caused by machines. Drawing upon the experiences of farmers and manufacturers of harvesting equipment who have completed this transition should prove useful in reducing the adjustment period and preventing injuries caused by lack of familiarity and poor design. The experience of farmers with even the most highly mechanized harvesting operations, however, suggests that the injury problem will not be totally eliminated. Contributions of operator error and machine design will continue to play a significant role in injury causation. But there is no question that in addition to greater productivity, the process of mechanization has significantly reduced the risks associated with harvesting.

 

Back

Thursday, 10 March 2011 14:44

Planting and Growing Operations

Modern agriculture is based on highly efficient equipment, especially high-speed, powerful tractors and agricultural machines. Tractors with mounted and trailed implements allow the mechanization of many agricultural operations.

Use of tractors allows farmers to accomplish the main tillage and care of plants in the optimum time without major manual labour. Permanent enlargement of farms, extension of land under cultivation and intensification of crop rotation promotes more efficient agriculture as well. Widespread use of high-speed assemblies is hampered by two factors: existing agricultural methods based mainly on machines and implements with passive tools; and difficulties in ensuring safe working conditions for the high-speed tractor assembly operator.

Mechanization can accomplish approximately 70% of planting and growing operations. It is used at all stages of crop cultivation and harvesting as well. Nevertheless, each stage of planting and growing has its own requisite set of machines, tools and environmental conditions, and this variability of the production and environmental factors has an influence upon the tractor driver.

Cultivation of the Land

Cultivation of the land (ploughing, harrowing, scuffing, disk harrowing, entire cultivation, rolling-down) is important and the most labour-intensive preliminary stage of crop production. These operations involve 30% of planting and growing operations.

As a rule, loosening of the soil results in the formation of dust. The nature of the dust in the air is variable, and depends on meteorological conditions, season, kind of work, type of soil and so on. Dust concentration in tractor cabs can vary from a few mg/m3 to hundreds of mg/m3, depending essentially on the cab enclosure. Approximately 60 to 65% of cases exceed the permissible total dust concentration level; permissible levels of respirable (less than or equal to 5 microns) dust are exceeded 60 to 80% of the time (see figure 1). Silica content in the dust varies from 0.5 to 20% (Kundiev 1983).

Figure 1. Tractor driver exposures to dust during land cultivation

AGR070F1

Cultivation consists of power-consuming operations, especially during ploughing, and it demands a considerable mobilization of the power resources of machines, generating considerable levels of noise where tractor drivers sit. These noise levels amount to 86 to 90 dBA and higher, creating a considerable risk of hearing disorders for these workers.

As a rule, whole-body vibration levels where the tractor driver is seated can be very high, exceeding levels established by the International Organization for Standardization (ISO 1985) for fatigue-decreased proficiency boundary and frequently for exposure limit.

Ground preparation is conducted mainly in early spring and autumn, so the microclimate of cabs in temperate zones for machines without air conditioners is not a health problem except on occasional hot days.

Sowing and Growing

Ensuring that sowing attachments or ploughing implements move in a straight line and that tractors follow marker tracks or the middle of the row are characteristic features of the sowing and care of crops.

In general, these activities require the driver to work in uncomfortable positions and involve considerable nervous and emotional tension due to restricted working-zone visibility, resulting in rapid development of operator fatigue.

The layout of sowing machines and their preparation for use, as well as the necessity of manual auxiliary work, especially materials handling, may involve considerable physical loads.

A wide geographical distribution of grain varieties results in a diversity of meteorological conditions when sowing. Winter crop sowing for different climate zones can be performed, for example, when the outdoor temperature ranges from 3–10 °C to 30–35 °C. Spring crop sowings are performed when the outdoor temperature ranges from 0 °C to 15–20 °C. The temperatures in tractor cabs without air conditioners can be very high in regions where climate is mild and hot.

Microclimate conditions in tractor cabs are favourable as a rule during tilled crops sowing (sugar beet, maize, sunflower) in temperate zones. Cultivation of crops is performed when the outdoor temperature is high and solar radiation is intense. The air temperature in cabs without microclimate control can rise to 40 °C and more. Tractor drivers can work under uncomfortable conditions about 40 to 70% of the total time involved in the care of crops.

Working operations for tilled crops cultivation involve considerable moving of earth, causing formation of dust. Maximum ground dust concentrations in the breathing zone air do not exceed 10 to 20 mg/m3. The dust is 90% inorganic, containing a large amount of free silica. Noise and vibration levels where the driver sits are a little lower than those existing during cultivation.

During sowing and cultivation, workers can be exposed to manures, chemical fertilizers and pesticides. When safety regulations for handling these materials are not followed, and if machines are not working properly, the breathing zone concentration of hazardous materials can exceed permissible values.

Harvesting

As a rule, harvesting lasts from 25 to 40 days. Dust, microclimate conditions and noise can be hazards during harvesting.

Breathing zone dust concentrations depend chiefly on outside concentration and the airtightness of the harvesting machine’s cab. Older machines without cabs leave drivers exposed to the dust. Dust formation is most intensive during the harvesting of dry corn, when the dust concentration at non-enclosed combines’ cabs can be as much as 60 to 90 mg/m3. Dust consists mainly of plant scraps, pollen and mushroom spores, mostly in large, nonrespirable particles (larger than 10 microns). Free silica content is less than 5.5%.

Formation of dust during sugar beet harvesting is lower. Maximum dust concentration at the cab does not exceed 30 mg/m3.

Harvesting of grain is generally performed in the hottest season. Temperature in the cab can rise to 36 to 40 °C. The flux level of direct solar radiation is 500 W/m2 and more when ordinary glass is used for cab windows. Tinted glass lowers the temperature of air in the cab by 1 to 1.6 °C. A mechanical forced ventilation system with a flow rate of 350 m3/h can create a temperature difference between inside and outside air of 5 to 7 °C. If the combine is equipped with adjustable louvers, this difference drops to 4 to 6 °C.

Tilled crops are harvested in the autumn months. As a rule conditions of the microclimate in cabs in this time are not a great health problem.

Experience in developed countries points to the fact that agriculture at small farms can be profitable with the use of small-scale mechanization (minitractors—motorized units with a capacity of up to 18 horsepower, with different kinds of auxiliary equipment).

Use of such equipment gives rise to a number of specific health problems. These problems include: intensification of workload in certain seasons, the use of child labour and the labour of elderly persons, absence of the means of protection against intensive noise, whole-body and local vibration, harmful meteorological conditions, dust, pesticides, and exhaust gases. The effort necessary to move the control levers of motorized units can amount to 60 to 80 N (newtons).

Some kinds of work are performed with the help of draught animals or done manually due to insufficient equipment or because of the impossibility of using machinery for some reason. Manual labour demands as a rule considerable physical effort. Power requirements during ploughing, horse-drawn sowing and manual mowing can amount to 5,000 to 6,000 cal/day and more.

Injuries are common during manual work, especially among inexperienced workers, and cases of plant burns, insect and reptile stings and dermatitis from the sap of some plants are frequent.

Prevention

One of the main trends in tractor construction is the improvement of working conditions of tractor operators. Side by side with perfection of the design of protective cabs is the search for ways of coordinating technical parameters of various tractor units with the functional abilities of operators. The aim of this research consists of ensuring the effectiveness of control and driving functions as well as necessary ergonomic parameters of the workplace environment.

Effectiveness of control and driving of tractor assemblies is ensured by good visibility of the working zone, by optimizing assemblies and control panel design and by proper ergonomic design of tractor seats.

Common ways of increasing visibility are increasing the viewing area of the cab using panoramic glass, improved layout of auxiliary equipment (e.g., fuel tank), rationalization of seat location, use of rear view mirrors and so on.

Optimization of construction control elements is connected with the construction of the control mechanism’s drive. Along with hydraulic and electric drives, a new improvement is suspended control pedals. This allows improved access and increased driving comfort. Functional coding (by means of form, colour and/or symbolic signs) plays an important part in recognition of the control elements.

Rational layout of instrumentation (which comprises 15 to 20 units in modern tractors) requires taking into account further increases in indicators due to remote control of technological process conditions, automation of the driving and operating of the technological equipment.

The operator’s seat is designed to guarantee a comfortable position and effective driving of the machine and tractor assembly. Design of modern tractor seats takes into account anthropometric data of the human body. Seats have adjustable back and arms and can be adjusted according to the operator’s size, in both horizontal and vertical dimensions (figure 2).

Figure 2. Angle parameters of optimal work posture of a tractor driver

AGR070F4

Precautions against harmful working conditions for tractor drivers include means of protection against noise and vibration, microclimate normalization and airtight sealing of cabs.

Besides special engineering of the engine to reduce noise at its source, considerable effect is achieved by mounting the engine on vibration isolators, isolating the cab from the tractor body with the help of shock absorbers and a number of measures designed for absorption of noise in the cab. Flaky, sound-absorbing lagging with a decorative surface is applied for this purpose to cab wall panels, and rugs made of rubber and porolon are laid on the cab floor. Hard perforated panelling with an air gap of 30 to 50 mm is applied to the ceiling. These measures have reduced noise levels in cabs to 80–83 dBA.

The main means of damping low-frequency vibration in the cab is use of an effective seat suspension. Nevertheless, the effect of whole-body vibration damping achieved this way does not exceed 20 to 30%.

Agricultural ground levelling gives considerable opportunities for decreasing vibration.

Improvement of the microclimate conditions in tractor cabs is reached with the help of both standard equipment (e.g., fans with filter elements, thermo-insulating tinted glass, sun-proof cap peaks, adjustable louvers) and special devices (e.g., air conditioners). Modern tractor heating systems are designed as an autonomous assembly attached to the engine’s cooling system and using warmed water to heat the air. Combined air conditioners and air heaters are also available.

Complex solutions of the problem of noise, vibration and heat isolation and sealing of cabs can be reached with the help of sealed cab capsules designed with suspended control pedals and wire rope systems of drives.

Ease of access to tractor engines and assemblies for their maintenance and repairs, as well as obtaining timely information about technical condition of certain units of the assembly, are important indices of the level of tractor operator working conditions. Eliminating the cab bonnet, forward inclination of the cab, detachable panels of the engine’s bonnet and so on are available in certain types of tractors.

In the future, tractor cabs are likely to be equipped with automatic control units, with television screens for observation of implements that are out of the operator’s field of vision and with units for conditioning of microclimate. Cabs will be mounted on outside rotary rods so they can be moved to a required position.

Rational organization of work and rest is of great importance for the prevention of fatigue and diseases of agricultural workers. In the hot season, daily routine ought to provide for working mainly in the morning and evening hours, reserving the hottest time for rest. During exhausting work (moving, hoeing), short regular breaks are necessary. Special attention has to be devoted to the rational, balanced nourishment of workers with due regard for the energy requirements of the tasks. Drinking regularly during the heat is of great importance. As a rule, workers drink traditional beverages (tea, coffee, fruit juices, infusions, broths and so on) in addition to water. Availability of sufficient amounts of wholesome liquids of high quality is very important.

Availability of comfortable overalls and personal protection equipment (PPE) (respirators, hearing protectors), especially during contact with dust and chemicals, is very important as well.

Medical control of the agricultural workers’ health has to be oriented to prevention of common occupational diseases, such as infectious diseases, chemical exposures, injuries, ergonomic problems and so forth. Teaching safe working methods, information about matters of hygiene and sanitation are of great importance.

 

Back

At the San Antonio farm, several workers became poisoned when applying the pesticide Lannate. An investigation of the case revealed that the workers had been using backpack sprayers for application without wearing any protective clothing, gloves or boots. Their employer had never provided the necessary equipment, and soap and showers were also unavailable. Following the poisonings, the employer was directed to take the appropriate corrective actions.

When the Ministry of Health made a follow-up inspection, they discovered that many farmers were still not using any protective clothing or equipment. When they were asked why, some said that the equipment was too hot and uncomfortable. Others explained that they had been working this way for years and never had any problems. Several commented that they didn’t need the equipment because they drank a large glass of milk after applying pesticides.

This experience, which took place in Nicaragua, is common to many parts of the world and illustrates the challenge to effective farmworker training. Training must be accompanied by provision of a safe work environment and legislative enforcement, but must also consider the barriers to implementing safe work practices and incorporate them in training programmes. These barriers, such as unsafe work environments, absence of protective equipment and attitudes and beliefs which are not health-promoting, should be directly discussed in training sessions, and strategies to address them should be developed.

This article describes an action-oriented training approach applied in two multidisciplinary pesticide projects that were designed to address the problem of farmworker pesticide poisoning. They were implemented in Nicaragua by CARE, Nicaragua and the American Friends Service Committee (1985 to 1989) and in the Central American region by the International Labour Organization (ILO, 1993 to present). In addition to a strong educational approach, the Nicaraguan project developed improved methods to mix and load pesticides, a medical monitoring plan to screen workers for overexposure to pesticides and a system to collect data for epidemiological investigation (Weinger and Lyons 1992). Within its multifaceted project, the ILO emphasized legislative improvements, training and building a regional network of pesticide educators.

Key elements of both projects were the implementation of a training needs assessment in order to tailor teaching content to the target audience, the use of a variety of participatory teaching approaches (Weinger and Wallerstein 1990) and the production of a teacher’s guide and educational materials to facilitate the learning process. Training topics included the health effects of pesticides, symptoms of pesticide poisoning, rights, resources and a problem-solving component which analysed the obstacles to working safely and how to resolve them.

Although there were many similarities between the two projects, the Nicaraguan project emphasized worker education while the regional project focused on teacher training. This article provides selected guidelines for both worker and teacher training.

Worker Education

Needs assessment

The first step in developing the training programme was the needs assessment or “listening phase”, which identified problems and obstacles to effective change, recognized factors which were conducive to change, defined values and beliefs held by the farmworkers and identified specific hazardous exposures and experiences which needed to be incorporated into the training. Walkthrough inspections were used by the Nicaraguan project team to observe work practices and sources of worker exposure to pesticides. Photographs were taken of the work environment and work practices for documentation, analysis and discussion during the training. The team also listened for emotional issues which might be barriers to action: worker frustration with inadequate personal protection, lack of soap and water or lack of safe alternatives to currently used pesticides.

Training methods and objectives

The next step in the training process was to identify the content areas to be covered utilizing information gained from listening to workers and then to select appropriate training methods based on the learning objectives. The training had four objectives: providing information; identifying and changing attitudes/emotions; promoting healthy behaviours; and developing action/problem-solving skills. What follows are examples of methods grouped under the objective which they best achieve. The following methods were incorporated into a 2-day training session (Wallerstein and Weinger 1992).

Methods for information objectives

Flipchart. In Nicaragua, the project staff needed visual educational tools which were easily portable and independent of electricity for use during field training or with medical screening on the farms. The flipchart included 18 drawings based on real-life situations, which were designed for use as discussion starters. Each picture had specific objectives and key questions that were outlined in an accompanying guide for instructors.

The flipchart could be used both to provide information and to promote problem analysis leading to action planning. For example, a drawing was used to provide information on the routes of entry by asking “How do pesticides enter the body?” To generate analysis of the problem of pesticide poisoning, the instructor would ask participants: “What’s happening here? Is this scene familiar? Why does this occur? What can (he) you do about it?” The introduction of two or more people into a drawing (of two people entering a recently sprayed field) encourages discussion of suspected motivations and feelings. “Why is she reading the sign? Why did he go right in?” With effective visual images, the same picture may trigger a variety of discussions, depending upon the group.

Slides. Slides which portray familiar images or problems were used in the same way as the flipchart. Using photos taken during the needs assessment phase, a slide show was created following the path of pesticide use from selection and purchase to disposal and clean-up at the end of the workday.

Methods for attitude-emotion objectives

Attitudes and emotions may effectively block learning and influence how health and safety practices are implemented back on the job.

Scripted role-play. A scripted role-play was often used to explore attitudes and trigger discussion of the problems of exposure to pesticides. The following script was given to three workers, who read their roles to the entire group.

Jose: What’s the matter?

Rafael: I’m about ready to give up. Two workers were poisoned today, just one week after that big training session. Nothing ever changes around here.

Jose: What did you expect? The managers didn’t even attend the training.

Sara: But at least they scheduled a training for the workers. That’s more than the other farms are doing.

Jose: Setting up a training is one thing, but what about follow-up? Are the managers providing showers and adequate protective equipment?

Sara: Have you ever thought that the workers might have something to do with these poisonings? How do you know they’re working safely?

Rafael: I don’t know. All I know is that two guys are in the hospital today and I have to go back to work.

The role-play was developed to explore the complex problem of pesticide health and safety and the multiple elements involved in resolving it, including training. In the discussion which followed, the facilitator asked the group if they shared any of the attitudes expressed by the farmworkers in the role-play, explored obstacles to resolving the problems portrayed and solicited strategies for overcoming them.

Worksheet questionnaire. In addition to serving as an excellent discussion starter and providing factual information, a questionnaire can also be a vehicle for eliciting attitudes. Sample questions for a farmworker group in Nicaragua were:

1. Drinking milk before work is effective in preventing pesticide poisoning.

    Agree            Disagree

    2. All pesticides have the same effect on your health.

      Agree            Disagree

       

      A discussion of attitudes was encouraged by inviting participants with conflicting viewpoints to present and justify their opinions. Rather than affirming the “correct” answer, the instructor acknowledged useful elements in the variety of attitudes that were expressed.

      Methods for behavioural skill objectives

      Behavioural skills are the desired competencies that workers will acquire as a result of training. The most effective way to achieve objectives for behavioural skill development is to provide participants with opportunities to practise in the class, to see an activity and perform it.

      Personal protective equipment demonstration. A display of protective equipment and clothing was laid out on a table in front of the class, including an array of appropriate and inappropriate options. The trainer asked a volunteer from the audience to get dressed for work applying pesticides. The farmworker chose clothing from the display and put it on; the audience was asked to comment. A discussion followed concerning appropriate protective clothing and alternatives to uncomfortable clothing.

      Hands-on practice. Both trainers and farmworkers in Nicaragua learned to interpret pesticide labels by reading them in small groups during the class. In this activity, the class was divided into groups and given the task of reading different labels as a group. For low-literacy groups, volunteer participants were recruited to read the label aloud and lead their group through a worksheet questionnaire on the label, which emphasized visual cues to determine level of toxicity. Back in the large group, volunteer spokespeople introduced their pesticide to the group with instructions for potential users.

      Methods for action/problem-solving objectives

      A primary goal of the training session is to provide farmworkers with the information and skills to make changes back on the job.

      Discussion starters. A discussion starter can be used to pose problems or potential obstacles to change, for analysis by the group. A discussion starter can take a variety of forms: a role-play, a picture in a flipchart or slide, a case study. To lead a dialogue on the discussion starter, there is a 5-step questioning process which invites participants to identify the problem, project themselves into the situation being presented, share their personal reactions, analyse the causes of the problem and suggest action strategies (Weinger and Wallerstein 1990).

      Case studies. Cases were drawn from real and familiar situations that occurred in Nicaragua that were identified in the planning process. They most commonly illustrated problems such as employer noncompliance, worker noncompliance with safety precautions within their control and the dilemma of a worker with symptoms that may be related to pesticide exposure. A sample case study was used to introduce this article.

      Participants read the case in small groups and responded to a series of questions such as: What are some of the causes of pesticide poisoning in this incident? Who’s benefiting? Who’s being harmed? What steps would you take to prevent a similar problem in the future?

      Action planning. Prior to the conclusion of the training session, participants worked independently or in groups to develop a plan of action to increase workplace health and safety when pesticides are used. Using a worksheet, participants identified at least one step they could take to promote safe working conditions and practices.

      Evaluation and Teacher Training

      Determining the extent to which the sessions met their objectives is a crucial part of training projects. Evaluation tools included a written post-workshop questionnaire and follow-up visits to farms as well as surveys and interviews with participants 6 months following the training session.

      Training teachers who would utilize the approach outlined above to provide information and training to farmworkers was an essential component of the ILO-sponsored Central American programmes. The objectives of the teacher training programme were to increase the knowledge on pesticide health and safety and the teaching skill of trainers; to increase the number and quality of training sessions directed toward farmworkers, employers, extension workers and agronomists in project countries; and to initiate a network of educators in pesticide health and safety in the region.

      Training topics in the 1-week session included: an overview of the health effects of pesticides, safe work practices and equipment; the principles of adult education; steps in planning an educational programme and how to implement them; demonstration of selected teaching methods; overview of presentation skills; practice teaching by participants using participatory methods, with critique; and development of action plans for future teaching about pesticides and alternatives to their use. A 2-week session allows time to conduct a field visit and training needs assessment during the workshop, to develop educational materials in the classroom and to conduct worker training sessions in the field.

      A trainer’s guide and sample curricula were provided during the workshop to facilitate practice teaching both in the classroom and following the workshop. The educators’ network offers another source of support and a vehicle for sharing innovative teaching approaches and materials.

      Conclusion

      The success of this teaching approach with workers in the cotton fields of Nicaragua, trade unionists in Panama and trainers from the Ministry of Health in Costa Rica, among others, demonstrates its adaptability to a variety of work settings and target groups. Its goals are not only to increase knowledge and skills, but also to provide the tools for problem-solving in the field after the teaching sessions have ended. One must be clear, however, that education alone cannot resolve the problems of pesticide use and abuse. A multidisciplinary approach which includes farmworker organizing, legislative enforcement strategies, engineering controls, medical monitoring and investigation into alternatives to pesticides is essential to effect comprehensive changes in pesticide practices.

       

      Back

      Thursday, 10 March 2011 14:37

      Floriculture

      Since the early 1990s, in many countries and across several continents, floriculture as an economic activity has been expanding rapidly. Its growing importance in export markets has resulted in an integrated development of several aspects of this field of activity, including production, technology, scientific research, transportation and conservation.

      Production

      The production of cut flowers has two essential components:

      1. the process of production, which involves all activities directly related to the generation and the development of the product up to the moment of packing
      2. the various activities that aid in the production and promote the marketing and distribution of cut flowers.

       

      The production process itself can be divided into three basic parts: germination, cultivation and post-harvest procedures.

      Germination is carried out by planting parent plants from which cuttings are obtained for cultivation.

      The cuttings of different flowers are planted on beds of a rooting medium. The beds are made from steam-treated dross and treated with chemical products to disinfect the growing medium and to facilitate root development.

      Cultivation is done in greenhouses which house the beds of rooting medium where the flowers are planted and grown as discussed in the article “Greenhouse and nursery operations” in this chapter and as shown in figure 1. Cultivation includes preparing the soil, planting the cuttings (figure 2) and harvesting the flowers.

      Figure 1. Tending flowers in a greenhouse

      AGR290F1

      Figure 2. Planting cuttings in a greenhouse

      AGR290F4

      Planting includes the cycle that begins with placing the cuttings in the rooting medium and ends with the flowering plant. It includes the following activities: planting, normal irrigation, drip irrigation with fertilizer, cultivation and weeding of the soil, pinching the tip of the plants to force branching and obtain more flowers, preparing the props that hold the plants upright, and the growth, branching and flowering of the plant.

      Production concludes with the gathering of the flowers and their separation by classification.

      At the post-harvest stage—in addition to selection and classification—the flowers are covered with plastic hoods, a sanitary treatment is applied, and they are packed for shipment.

      Secondary activities include monitoring the health of the plants to detect pests and to diagnose plant illnesses early, obtaining raw materials from the warehouse, and maintaining the furnaces.

      Health Risk Factors

      The most important risk factors in each of the different areas of work are:

      • chemical substances
      • extreme temperatures—heat
      • non-ionizing radiation
      • infectious disease
      • ergonomic factors
      • mechanical factors
      • psychosocial factors.

       

      Chemical substances

      Intoxication and chronic illness due to pesticides

      The levels of morbidity/mortality found in workers due to exposure to pesticides are not the consequence of a simple relation between the chemical agent and the person who has suffered exposure to it, but also reflect the interplay of many other factors. Among these are the length of exposure, individual susceptibility, the nutritional state of the person exposed, educational and cultural variables and the socioeconomic conditions under which the workers live.

      In addition to the active ingredients of pesticides, the substances that convey the active ingredients and the additives should also be taken into consideration, because sometimes those substances can have adverse effects that are more harmful than those of the active ingredients.

      The toxicity of pesticides made with organophosphates is due to their effect on the central nervous system, because they inhibit the activity of the enzyme acetylcholinesterase. The effects are cumulative, and delayed effects have also been noted on the central and the peripheral nervous systems. According to studies carried out in several countries, the prevalence of inhibition of this enzyme among workers who handle these pesticides fluctuates between 3 and 18%.

      The long-term effects are pathological processes that develop after a latency period and are due to repeated exposures. Among the long-term effects known to be due to pesticide exposure are skin lesions, nerve damage and mutagenic effects.

      Respiratory problems

      Decorative plants can irritate the respiratory system and cause coughing and sneezing. In addition, plant scents or odours may exacerbate symptoms of asthma or allergic rhinitis, although they have not been shown to cause allergies. Pollen from the chrysanthemum and the sunflower can cause asthma. Dust from dried plants sometimes causes allergies.

      Dermatitis

      The cases of occupational dermatitis found in floriculture are about 90% primarily due to contact dermatitis. Of these, about 60% are caused by primary irritants and 40% are due to allergic reactions. The acute form is characterized by reddening (erythema), swelling (oedema), pimples (papules), vesicles or blisters. It is especially localized on the hands, wrists and forearms. The chronic form can have deep fissures, lichenification (thickening and hardening) of the skin, and severe xerosis (dryness). It can be incapacitating and even irreversible.

      Floriculture is one of those activities where contact with primary irritants or allergenic substances is high, and for that reason it is important to promote and use preventive measures, such as gloves.

      Extreme temperatures—heat

      When work must be carried out in a hot environment, as in the case of hothouses, the thermal load on the worker is the sum of the heat of the work environment plus the energy expended on the task itself.

      Physical effects of excessive exposure to heat include heat rash, cramps and muscle spasms, exhaustion and fainting spells. Heat rash, in addition to being uncomfortable, lowers the worker’s tolerance to heat. If perspiration is abundant and liquids and electrolytes are not replenished adequately, cramps and muscle spasms can set in. Heat exhaustion occurs when vasomotor control and cardiac output are insufficient to compensate for the additional demands placed on these systems by the heat stress. Fainting spells represent a very serious clinical situation that can lead to confusion, delirium and coma.

      Precautions include frequent rest breaks in cool areas, availability of beverages to drink, rotating of tasks requiring heavy exertion and wearing of light-coloured clothing.

      Non-ionizing radiation

      The most important kinds of non-ionizing radiation that floriculture workers are exposed to are ultraviolet (UV) radiation, visible light and infrared radiation. The most serious effects of UV radiation are solar erythema, actinic dermatitis, irritative conjunctivitis and photokeratitis.

      Radiation from the visible spectrum of light may cause retinal and macular degeneration. One symptom of exposure to infrared radiation is superficial burn of the cornea, and prolonged exposure can lead to the premature appearance of cataracts.

      Precautions include keeping the skin covered, wearing tinted glasses, and medical surveillance.

      Ergonomic factors

      Workers who maintain a static body posture for long periods of time (see figure 3) can suffer from resulting static muscle contractions and from alterations of the peripheral, vascular and nervous systems. Repetitive movements are more common in tasks that require manual dexterity. For example, clipping shears can require a lot of force and involve repetitive motion. The most frequently observed effects are musculoskeletal impairments, including tendinitis of the elbow and wrist, carpal tunnel syndrome and impairment of movement at the shoulder.

      Figure 3. Bending over for extended periods is a common cause of ergonomic problems

      AGR290F2

      Job rotation and the proper ergonomic design of equipment such as clipping shears are needed precautions. Redesigning the workplace to require less bending is another solution.

      Infectious diseases

      Floriculture may expose workers to a variety of biological agents. Early signs of an infection are rarely specific, although they are generally well-defined enough to lead to a suspicion of illness. The signs, symptomatology and precautions depend on the agent, which includes tetanus, rabies, hepatitis and so on. Preventive measures include a source of potable water, good sanitary facilities, first aid and medical care for cuts and abrasions.

      Other factors

      The most common health and safety hazards associated with mechanical factors are cuts, abrasions and single and multiple traumas, which most frequently injure the hands and face. Such injuries must be attended to immediately. Workers should have up-to-date tetanus shots and adequate first-aid facilities must be available.

      The psychosocial environment can also endanger worker health. The results of exposure to these factors can have the following consequences: physiological changes (indigestion, constipation, palpitations, difficulty breathing, hyperventilation, insomnia and anxiety); psychological disturbances (tension and depression); and behavioural disturbances (absenteeism, instability, dissatisfaction).

       

      Back

      Thursday, 10 March 2011 14:26

      Greenhouse and Nursery Operations

      The nursery industry raises plants for the replanting market (see figure 1). Hardy plants are grown outside, and the less hardy plants are propagated and raised inside, typically in greenhouses, to protect them from cold temperatures or too much solar radiation or wind. Many plants grown inside during harsh growing conditions are grown outside in favourable weather conditions. Typical nursery crops are trees and shrubs, and the typical greenhouse crops include flowers, vegetables and herbs. The nursery industry grows plants for the replanting market, but greenhouses are also used for growing crops for seasonal markets, such as tomatoes during the freezing months of winter.

      Figure 1. Setting coffee plants in a nursery in Cote d’Ivoire

      AGR280F1

      The plant nursery industry constitutes a large and growing sector of agriculture. In California, where there are more than 3,000 commercial nursery operations, nursery crops are a high value-per-acre commodity, ranking fifth in state farm income. As with much of western US agriculture, the employee population is dominated by workers from Mexico or other Central American countries. The majority of these workers are not migrant, but are settled in local communities with their families (Mines and Martin 1986). Most speak Spanish only or as a primary language and have little or no formal education. Wages are low for most jobs, and there is a labour surplus. Similar situations exist throughout the world.

      Nursery work is considered a comparatively good job by most agricultural workers because it is year-round, comparatively well-paid and frequently includes workers’ compensation insurance and employee health benefits. Few workers belong to labour organizations in this industry, and most workers are employed directly by the enterprise rather than by farm labour contractors.

      Greenhouses provide a controlled environment for plants and are used for a variety of purposes, which include growing rare and exotic plants, protecting producing plants (such as flowers, tomatoes and peppers) from winter weather and starting seedlings. The controlled environment within a greenhouse is advantageous to those who wish to grow crops year-round, regardless of seasonal conditions outdoors. Greenhouse operations have expanded in temperate climates. For example, in the Ukraine, the total area of greenhouses has grown from 3,070 hectares (ha) in 1985 to 3,200 ha in 1990 to an estimated 3,400 ha in 1995 (Viten, Krashyyuh and Ilyna 1994).

      The gable (equal sloping roof) greenhouse is typical. It provides good exposure to winter sunlight, drainage and wind protection. The framing materials for greenhouses include wood, aluminium or a combination of steel pipe and wood. Side walls or siding can be made from a variety of materials including plywood, aluminium, wood or vinyl. In the Ukraine, 60% of the greenhouses have masonry block walls. Covers include glass or plastic, and in some parts of the world, the glass-covered house is called a glasshouse. The plastic can be either rigid or a flexible film. Rigid plastics used as covers include fibreglass, acrylic and polycarbonate. Flexible plastic covers include polyethylene, polyvinyl chloride and polyester. Polycarbonate, which withstands breakage from thrown objects, and the flexible plastics require frequent replacement. Covers can vary from clear to opaque, and they serve three purposes. One is to let sunlight in for the plants. Another is for heating within an enclosure. The last is protecting the plants from environmental stress, including snow, rain, hail, high winds, birds, small animals and insects.

      The greenhouse operation requires the control of temperature, humidity and ventilation, using artificial heat sources, exhaust and inlet fans, shading (such as with movable slats or netting), cooling equipment (such as wet-pad or evaporative cooling), humidification and climate-control equipment (Jones 1978).

      Nursery and greenhouse workers are exposed to a variety of hazards, including skin irritants, dust, noise, heat stress, musculoskeletal disorders (sprains and strains), pesticides and injuries related to vehicles, machines, slips and falls and electricity. The hazards discussed below are limited to ergonomic hazards in nursery work and pesticide hazards in greenhouse work. Many of these hazards are common for the two operations.

      Nursery Operations

      Typical operations at a large wholesale nursery specializing in container-grown outdoor bedding and ornamental plants consist of four stages:

        1. Propagation stage. New plants are started in a specialized medium using one of four standard methods: cuttings from mature plants, tissue culture, seeds and grafting.
        2. Replanting stage. As plants grow they are replanted into individual plastic containers called “cans” (typically 2 or 3 times during the early growth cycle). A powered conveyor carries the new, larger cans past a hopper where they are filled with soil. As the cans continue down the conveyor, plants are manually transplanted into them, and finally they are manually transferred onto a trailer for transport to the field.
        3. Growing stage or field operations. Plants are held in outdoor groups until fully mature. During this period, tasks include watering, pruning, fertilizing and weeding, tying-staking-shaping and spacing as plants grow.
        4. Shipping. Mature plants are removed to the shipping area, labelled, organized by order load, and loaded into trucks. This operation can also include truck unloading at retail sites.

               

              Ergonomic hazards

              Nursery work, as with other agricultural commodities, has a pattern of high rates of sprain and strain injuries. AgSafe data (1992) suggest that 38.9% of all reported injuries in horticultural specialties (including nurseries) were sprains and strains, slightly above the proportion for agriculture as a whole. Overexertion as a cause of injury for this area was cited for 30.2% of reported injuries, also above the proportion for the industry as a whole.

              The most common risk factors for the development of work-related musculoskeletal problems have been identified as occurring in the following job tasks:

              During propagation, the worker stands or sits at a work table, empties a basket of plant cuttings, and uses hand shears to cut them into smaller pieces. The shears are held in the dominant hand; plant material is grasped with the other hand. After each piece of plant material is cut, the shears must be disinfected by dipping them in a solution in a small container in the work bench.

              When cutting, one hand is engaged in very repetitive gripping, with an average of 50 to 60 cuts per minute. Mild to moderate wrist flexion and ulnar deviation occur throughout the cutting cycle. The other hand is used to hold the cuttings, orient them for cutting, and discard the remains in a bin. Moderate wrist extension and ulnar deviation occur throughout this cycle also.

              Workers in this specialized job are highly skilled and work virtually full-time year-round without rotation into other jobs. Workers report pain and numbness in the hand, wrist and arm. After a period of years on this job, they demonstrate an elevated incidence of carpal tunnel syndrome.

              In transporting plants from a conveyor belt to a trailer, the worker grasps 3 or 4 3.8-litre containers in each hand and places them on a trailer located either to one side of or behind him or her. This job cycle is repeated 13 to 20 times per minute. Risk factors include highly repetitive gripping, high pinch forces and awkward postures, including trunk, lumbar and shoulder flexion.

              In transporting plants from a trailer to a planting bed, the worker grasps 3 or 4 3.8-l containers in each hand, carries them up to 17 m, and places them on the ground along a predetermined row. This job cycle is repeated 3 to 5 times per minute. Handling cans is a nearly full-time, year-round job for many workers. It is associated with pain in the fingers and hands, upper extremities and lower back. Because field workers tend to be younger, the predicted high rate of chronic back injury is not documented at this time.

              The pruner works with various shears to snip unwanted or dead parts off the tops and sides of plants. The worker is usually standing or bent over to reach plants. The dominant hand holds the shears and is engaged in very repetitive gripping, with an average of 40 to 50 cuts per minute. The fingers of the same hand are also used to pinch off small twigs or other plant parts. The nondominant hand grasps the can for a rapid pick and place, and also holds the cuttings in a static grip with a moderate wrist flexion and ulnar deviation present throughout the cutting cycle. Because pruning is a part-time task for most field workers, some relief and recovery are achieved due to task variation. However, it is associated with pain in the fingers and hand, wrist, upper extremities and lower back.

              To allow plants adequate room to grow and expand, spacing must be done periodically. This entails grasping and lifting 3 to 4 plants in each hand, carrying them a short distance, and placing them on the ground in rows. This cycle is repeated 3 to 5 times per minute. Like pruning, spacing is a part-time task for most field workers, allowing opportunity for relief and recovery. It is also associated with pain in fingers and hands, wrists, upper extremities and lower back.

              Most nursery jobs are human-energy intensive, and this, coupled with the repetitive nature of many tasks, leads to substantial risk of repetitive-motion injuries. Tools to assist the workers by improving body posture and reducing the energy requirements of particular tasks have just begun to be developed.

              Greenhouse Operations

              Typical operations in a greenhouse vary depending on whether the purpose is to grow rare and exotic plants, production plants or seedlings. The growing of rare or exotic plants is a year-round enterprise. Production plants are typically grown within the greenhouse to protect them from the weather; thus, greenhouses can be used seasonally. The growth of seedlings is similar to nursery operations, but the market is plants for spring replanting after the last freeze. The tasks involved in greenhouse growing include putting the soil into small containers, planting the seed in each of the containers, watering and fertilizing the plants, trimming or thinning the plants as needed (see figure 2), applying fumigants or pesticides and transporting the plants or product from the greenhouse. Soil filling and planting has become a mechanized operation in the production greenhouse. The composition of the potting soil may be a mix of peat, perlite and vermiculite. Trimming may be mechanized, depending upon the crop. Watering may be directly with a hose or through an automated sprinkler or piping system. Nutrients are added to the water to fertilize the plants. Application of pesticides by hand sprayer is typical. Soil sterilization is done either by steam or chemicals, including dibromochloropropane (DBCP). The transport of plants or product is typically a manual exercise.

              Figure 2. Clipping (mowing) tobacco transplants in a greenhouse in North Carolina

              AGR280F2

              Pesticides Used in Greenhouses

              Diseases and insects that attack plants can result in major problems for greenhouse operators. Often, preventing such damage is easier than trying to eradicate the pests afterward. Some common pests that inflict the most damage on greenhouse crops are insects, fungi, viruses, bacteria and nematodes. To combat these undesirable organisms, special chemicals (pesticides) are applied to the plants to kill the pests.

              There are many ways of applying pesticides so that they are effective. The most common application methods are: liquid sprays, mists, dusts, fogs, smokes, aerosol canisters and granules. Pesticide sprays involve the use of a water/pesticide mixture contained in a tank that has a hose with a spray nozzle attached to it. Under pressure, the mixture is directed onto the plants as liquid droplets. Mists are generated by a technique similar to the spray technique, but the resulting droplets are smaller. Pesticide dusts are often released into the air and allowed to settle onto the plant surface. Foggers use heating devices to generate very small droplets directed at the plants. Pesticide smokes are generated by igniting a sparkler and placing it in a canister that contains the chemical.

              Aerosol canisters are pressurized metal containers that release the pesticide to the air when a valve is opened. Finally, granular pesticides are placed on top of the soil and then watered. The watering dissolves the granules and transports the chemical to the roots of the plant, where it can either kill organisms in the soil or be absorbed by the plant and kill organisms that feed on it.

              With each different method of application of a pesticide comes the hazard of being exposed to the chemical. The two most common routes of exposure are through the skin (dermal) and through the lungs (respiratory). Another, but less common, route of exposure is by ingesting food or drinks contaminated with pesticides. Greenhouse workers who handle the chemicals or the treated plants may be poisoned if proper safety precautions are not followed.

              Ways to avoid poisoning include proper use of greenhouse ventilation systems, using and maintaining the appropriate PPE (suits, gloves, respirators, boots—see figure 3), observing recommended re-entry times and following the pesticide label instructions. Some additional safety precautions are: storage of all pesticides inside a locked, well-ventilated area; posting signs in areas where plants have been treated; and comprehensive pesticide training that includes proper application and handling techniques. Finally, all pesticide applicators should be trained in appropriate disposal techniques for old pesticides and empty pesticide containers.

              Figure 3. Worker in full protective gear applies pesticides in a greenhouse.

              AGR290F3

               

              Back

              Page 71 of 122

              " DISCLAIMER: The ILO does not take responsibility for content presented on this web portal that is presented in any language other than English, which is the language used for the initial production and peer-review of original content. Certain statistics have not been updated since the production of the 4th edition of the Encyclopaedia (1998)."

              Contents

              Health Care Facilities and Services References

              Abdo, R and H Chriske. 1990. HAV-Infektionsrisiken im Krankenhaus, Altenheim und Kindertagesstätten. In Arbeitsmedizin im Gesundheitsdienst, Band 5, edited by F Hofmann and U Stössel. Stuttgart: Gentner Verlag.

              Acton, W. 1848. On the advantages of caouchoue and gutta-percha in protecting the skin against the contagion of animal poisons. Lancet 12:588.

              Ahlin, J. 1992. Interdisciplinary case studies in offices in Sweden. In Corporate Space and Architecture. Vol. 2. Paris: Ministére de l’équipment et du logement.

              Akinori, H and O Hiroshi. 1985. Analysis of fatigue and health conditions among hospital nurses. J Science of Labour 61:517-578.

              Allmeers, H, B Kirchner, H Huber, Z Chen, JW Walter, and X Baur. 1996. The latency period between exposure and the symptoms in allergy to natural latex: Suggestions for prevention. Dtsh Med Wochenschr 121 (25/26):823-828.

              Alter, MJ. 1986. Susceptibility to varicella zoster virus among adults at high risk for exposure. Infec Contr Hosp Epid 7:448-451.

              —. 1993. The detection, transmission, and outcome of hepatitis C infection. Infect Agents Dis 2:155-166.

              Alter, MJ, HS Margolis, K Krawczynski, FN Judson, A Mares, WJ Alexander, PY Hu, JK Miller, MA Gerber, and RE Sampliner. 1992. The natural history of community-acquired hepatitis C in the United States. New Engl J Med 327:1899-1905.

              American Conference of Governmental Industrial Hygienists (ACGIH). 1991. Documentation of the Threshold Limit Values and Biological Exposure Indices, 6th edition. Cincinnati, OH: ACGIH.

              —. 1994. TLVs: Threshold Limit Values and Biological Exposure Indices for 1994-1995. Cincinnati, OH: ACGIH.

              American Hospital Association (AHA). 1992. Implementing Safer Needle Practice. Chicago, IL: AHA.

              American Institute of Architects. 1984. Determining Hospital Space Requirements. Washington, DC: American Institute of Architects Press.

              American Institute of Architects Committee on Architecture for Health. 1987. Guidelines for Construction and Equipment of Hospital and Medical Facilities. Washington, DC: American Institute of Acrchitects Press.

              American Society of Heating, Refrigerating and Air-conditioning Engineers (ASHRAE). 1987. Health facilities. In ASHRAE Handbook: Heating, Ventilating and Air-conditioning Systems and Applications. Atlanta, GA: ASHRAE.

              Anon. 1996. New drugs for HIV infection. Medical Letter of Drugs and Therapeutics 38:37.

              Axelsson, G, R Rylander, and I Molin. 1989. Outcome of pregnancy in relation to irregular and inconvenient work schedules. Brit J Ind Med 46:393-398.

              Beatty, J SK Ahern, and R Katz. 1977. Sleep deprivation and the vigilance of anesthesiologists during simulated surgery. In Vigilance, edited by RR Mackie. New York: Plenum Press.

              Beck-Friis, B, P Strang, and PO Sjöden. 1991. Work stress and job satisfaction in hospital-based home care. Journal of Palliative Care 7(3):15-21.

              Benenson, AS (ed.). 1990. Control of Communicable Disease in Man, 15th edition. Washington, DC: American Public Health Association.

              Bertold, H, F Hofmann, M Michaelis, D Neumann-Haefelin, G Steinert, and J Wölfle. 1994. Hepatitis C—Risiko für Beschäftigte im Gesundheitsdienst? In Arbeitsmedizin im Gesundheitsdienst, Band 7, edited by F Hofmann, G Reschauer, and U Stössel. Stuttgart: Gentner Verlag.

              Bertram, DA. 1988. Characteristics of shifts and second-year resident performance in an emergency department. NY State J Med 88:10-14.

              Berufsgenossenschaft für Gesundheitsdienst und Wohlfahrtspflege (BGW). 1994. Geschäftsbericht.

              Bissel, L and R Jones. 1975. Disabled doctors ignored by peers. Presented at the American Medical Association Conference on the Imparied Physician, 11 April, San Francisco, CA.

              Bitker, TE. 1976. Reaching out to the depressed physician. JAMA 236(15):1713-1716.

              Blanchard, M, MM Cantel, M Faivre, J Girot, JP Ramette, D Thely, and M Estryn-Béhar. 1992. Incidence des rythmes biologiques sur le travail de nuit. In Ergonomie à l’hôpital, edited by M Estryn-Béhar, C Gadbois, and M Pottier. Toulouse: Edition Octares.

              Blanpain, C and M Estryn-Béhar. 1990. Measures d’ambiance physique dans dix services hospitaliers. Performances 45:18-33.

              Blaycock, B. 1995. Latex allergies: Overview, prevention and implications for nursing care. Ostomy Wound Manage 41(5):10-12,14-15.

              Blazer, MJ, FJ Hickman, JJ Farmer, and DJ Brenner. 1980. Salmonella typhi: The laboratory as a reservoir of infection. Journal of Infectious Diseases 142:934-938.

              Blow, RJ and MIV Jayson. 1988. Back pain. In Fitness for Work: The Medical Approach, edited by FC Edwards, RL McCallum, and PJ Taylor. Oxford: Oxford University Press.

              Boehm, G and E Bollinger. 1990. Significance of environmental factors on the tolerated enteral feeding volumes for patients in neonatal intensive care units. Kinderarzliche Praxis 58(6):275-279.

              Bongers, P, RD Winter, MAJ Kompier, and VV Hildebrandt. 1992. Psychosocial Factors at Work and Musculoskeletal Diseases. Review of the literature. Leiden, Netherlands: TNO.

              Bouhnik, C, M Estryn-Béhar, B Kapitaniak, M Rocher, and P Pereau. 1989. Le roulage dans les établissements de soins. Document pour le médecin du travail. INRS 39:243-252.

              Boulard, R. 1993. Les indices de santé mentale du personnel infirmier: l’impact de la charge de travail, de l’autonomie et du soutien social. In La psychologie du travail à l’aube du XXI° siècle. Actes du 7° Congrès de psychologie du travail de langue française. Issy-les-Moulineaux: Editions EAP.

              Breakwell, GM. 1989. Facing Physical Violence. London: British Psychological Society.

              Bruce, DL and MJ Bach. 1976. Effects of Trace Concentrations of Anesthetic Gases on Behavioral Performance of Operating Room Personnel. DHEW (NIOSH) Publication No. 76-169. Cincinnati, OH: NIOSH.

              Bruce, DL, KA Eide, HW Linde, and JE Eckenhoff. 1968. Causes of death among anesthesiologists: A 20 years survey. Anesthesiology 29:565-569.

              Bruce, DL, KA Eide, NJ Smith, F Seltzer, and MH Dykes. 1974. A prospective survey of anesthesiologists’ mortality, 1967-1974. Anesthesiology 41:71-74.

              Burhill, D, DA Enarson, EA Allen, and S Grzybowski. 1985. Tuberculosis in female nurses in British Columbia. Can Med Assoc J 132:137.

              Burke, FJ, MA Wilson, and JF McCord. 1995. Allergy to latex gloves in clinical practice: Case reports. Quintessence Int 26(12):859-863.

              Buring, JE, CH Hennekens, SL Mayrent, B Rosner, ER Greenberg, and T Colton. 1985. Health experiences of operating room personnel. Anesthesiology 62: 325-330.

              Burton, R. 1990. St. Mary’s Hospital, Isle of Wight: A suitable background for caring. Brit Med J 301:1423-1425.

              Büssing, A. 1993. Stress and burnout in nursing: Studies in different work structures and work schedules. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Cabal, C, D Faucon, H Delbart, F Cabal, and G Malot. 1986. Construction d’une blanchisserie industrielle aux CHU de Saint-Etienne. Arch Mal Prof 48(5):393-394.

              Callan, JR, RT Kelly, ML Quinn, JW Gwynne, RA Moore, FA Muckler, J Kasumovic, WM Saunders, RP Lepage, E Chin, I Schoenfeld, and DI Serig. 1995. Human Factors Evaluation of Remote Afterloading Brachytherapy. NUREG/CR-6125. Vol. 1. Washington, DC: Nuclear Regulatory Commission

              Cammock, R. 1981. Primary Health Care Buildings: Briefing and Design Guide for Architects and Their Clients. London: Architectural Press.

              Cardo, D, P Srivastava, C Ciesielski, R Marcus, P McKibben, D Culver, and D Bell. 1995. Case-control study of HIV seroconversion in health care workers after percutaneous exposure to HIV-infected blood (abstract). Infect Control Hosp Epidemiol 16 suppl:20.

              Carillo, T, C Blanco, J Quiralte, R Castillo, M Cuevas, and F Rodriguez de Castro. 1995. Prevalence of latex allergy among greenhouse workers. J Allergy Clin Immunol 96(5/1):699-701.

              Catananti, C and A Cambieri. 1990. Igiene e Tecnica Ospedaliera (Hospital Hygiene and Organization). Roma: II Pensiero Scientifico Editore.

              Catananti, C, G Damiani, G Capelli, and G Manara. 1993. Building design and selection of materials and furnishings in the hospital: A review of international guidelines. In Indoor Air ’93, Proceedings of the 6th International Conference on Indoor Air Quality and Climate 2:641-646.

              Catananti, C, G Capelli, G Damiani, M Volpe, and GC Vanini. 1994. Multiple criteria evaluation in planning selection of materials for health care facilities. Preliminary identification of criteria and variables. In Healthy Buildings ’94, Proceedings of the 3rd International Conference 1:103-108.

              Cats-Baril, WL and JW Frymoyer. 1991. The economics of spinal disorders. In The Adult Spine, edited by JW Frymoyer. New York: Raven Press.

              Centers for Disease Control (CDC). 1982. Acquired immunodeficiency syndrome (AIDS): Precautions for clinical laboratory staffs. Morb Mortal Weekly Rep 31:577-580.

              —. 1983. Acquired immunodeficiency syndrome (AIDS): Precautions for health-care workers and allied professionals. Morb Mortal Weekly Rep 32:450-451.

              —. 1987a. Human immunodeficiency virus infection in health-care workers exposed to blood of infected patients. Morb Mortal Weekly Rep 36:285-289.

              —. 1987b. Recommendations for prevention of HIV transmission in health-care settings. Morb Mortal Weekly Rep 36 suppl 2:3S-18S.

              —. 1988a. Universal precautions for prevention of transmission of human immunodeficiency virus, hepatitis B virus, and other bloodborne pathogens in health-care settings. Morb Mortal Weekly Rep 37:377-382,387-388.

              —. 1988b. Guidelines for prevention of transmission of human immunodeficiency virus and hepatitis B virus to health-care and public-safety workers. Morb Mortal Weekly Rep 37 suppl 6:1-37.

              —. 1989. Guidelines for prevention of transmission of human immunodeficiency virus and hepatitis B virus to health-care and public-safety workers. Morb Mortal Weekly Rep 38 suppl 6.

              —. 1990. Public Health Service statement on management of occupational exposure to human immunodeficiency virus, including considerations regarding post-exposure use. Morb Mortal Weekly Rep 39 (No. RR-1).

              —. 1991a. Hepatitis B virus: A comprehensive strategy for eliminating transmission in the United States through universal childhood vaccination: Recommendations of the Immunization Practices Advisory Committee (ACIP). Morb Mortal Weekly Rep 40 (No. RR-13).

              —. 1991b. Recommendations for preventing transmission of human immunodeficiency virus and hepatitis B virus to patients during exposure-prone invasive procedures. Morb Mortal Weekly Rep 40 (No. RR-8).

              —. 1993a. Recommended infection-control practices in dentistry. Morb Mortal Weekly Rep 42 (No. RR-8):1-12.

              —. 1993b. Biosafety in Microbial and Biomedical Laboratories, 3rd edition. DHHS (CDC) Publication No. 93-8395. Atlanta, GA: CDC.

              —. 1994a. HIV/AIDS Surveillance Report. Vol. 5(4). Atlanta, GA: CDC.

              —. 1994b. HIV/AIDS Prevention Newsletter. Vol. 5(4). Atlanta, GA: CDC.

              —. 1994c. Human immunodeficiency virus in household settings—United States. Morb Mortal Weekly Rep 43:347-356.

              —. 1994d. HIV/AIDS Surveillance Report. Vol. 6(1). Atlanta, GA: CDC.

              —. 1994e. Guidelines for preventing the transmission of Mycobacterium tuberculosis in health-care facilities. Morb Mortal Weekly Rep 43 (No. RR-13):5-50.

              —. 1995. Case-control study of HIV seroconversion in health-care workers after percutaneous exposure to HIV-infected blood—France, United Kingdom, and United States. Morb Mortal Weekly Rep 44:929-933.

              —. 1996a. HIV/AIDS Surveillance Report. Vol 8(2). Atlanta, GA: CDC.

              —. 1996b. Update: Provisional Public Health Service recommendations for chemoprophylaxis after occupational exposure to HIV. Morb Mortal Weekly Rep 45:468-472.

              Charney, W (ed.). 1994. Essentials of Modern Hospital Safety. Boca Raton, FL: Lewis Publishers.

              Chou, T, D Weil, and P Arnmow. 1986. Prevalence of measles antibodies in hospital personnel. Infec Contr Hosp Epid 7:309-311.

              Chriske, H and A Rossa. 1991. Hepatitis-C-Infektionsgefährdung des medizinischen Personals. In Arbeitsmedizin im Gesundheitsdienst, Band 5, edited by F Hofmann and U Stössel. Stuttgart: Gentner Verlag.

              Clark, DC, E Salazar-Gruesco, P Grabler, J Fawcett. 1984. Predictors of depression during the first 6 months of internship. Am J Psychiatry 141:1095-1098.

              Clemens, R, F Hofmann, H Berthold, and G Steinert. 1992. Prävalenz von Hepatitis, A, B und C bei Bewohern einer Einrichtung für geistig Behinderte. Sozialpädiatrie 14:357-364.

              Cohen, EN. 1980. Anasthetic Exposure in the Workplace. Littleton, MA: PSG Publishing Co.

              Cohen, EN, JW Bellville, and BW Brown, Jr. 1971. Anesthesia, pregnancy and miscarriage: A study of operating room nurses and anesthetists. Anesthesiology 35:343-347.

              —. 1974. Occupational disease among operating room personnel: A national study. Anesthesiology 41:321-340.

              —. 1975. A survey of anethestic health hazards among dentists. J Am Dent Assoc 90:1291-1296.

              Commission of the European Communities. 1990. Recommendation of the Commission February 21, 1990, about Protection of People against Exposure to Radon in Indoor Environments. 90/143/Euratom (Italian Translation).

              Cooper, JB. 1984. Toward prevention of anesthesic mishaps. International Anesthesiology Clinics 22:167-183.

              Cooper, JB, RS Newbower, and RJ Kitz. 1984. An analysis of major errors and equipment failures in anesthesia management: Considerations for prevention and detection. Anesthesiology 60(1):34-42.

              Costa, G, R Trinco, and G Schallenberg. 1992. Problems of thermal comfort in an operating room equipped with laminar air flow system In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar M, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Cristofari, M-F, M Estryn-Béhar, M Kaminski, and E Peigné. 1989. Le travail des femmes à l’hôpital. Informations Hospitalières 22/23:48-62.

              Council of the European Communities. 1988. Directive December 21, 1988, to Draw Near the Laws of Member Countries about Building Products. 89/106/EEC (Italian translation).

              de Chambost, M. 1994. Alarmes sonnantes, soignantes trébuchantes. Objectif soins 26:63-68.

              de Keyser, V and AS Nyssen. 1993. Les erreurs humaines en anesthésies. Le Travail humain 56(2/3):243-266.

              Decree of the President of Ministers Council. 1986. Directive to the Regions about Private Health Care Facilities Requirements. 27 June.

              Dehlin, O, S Berg, GBS Andersson, and G Grimby. 1981. Effect of physical training and ergonomic counselling on the psychosocial perception of work and on the subjective assesment of low-back insuffuciency. Scand J Rehab 13:1-9.

              Delaporte, MF, M Estryn-Béhar, G Brucker, E Peigne, and A Pelletier. 1990. Pathologie dermatologique et exercice professionnel en milieu hospitalier. Arch Mal Prof 51(2):83-88.

              Denisco, RA, JN Drummond, and JS Gravenstein. 1987. The effect of fatigue on the performance of a simulated anesthetic monitoring task. J Clin Monit 3:22-24.

              Devienne, A, D Léger, M Paillard, A Dômont. 1995. Troubles du sommeil et de la vigilance chez des généralistes de garde en région parisienne. Arch Mal Prof 56(5):407-409.

              Donovan, R, PA Kurzman, and C Rotman. 1993. Improving the lives of home care workers: A partnership of social work and labor. Soc Work 38(5):579-585..

              Edling, C. 1980. Anesthetic gases as an occupational hazard. A review. Scand J Work Environ Health 6:85-93.

              Ehrengut, W and T Klett. 1981. Rötelnimmunstatus von Schwesternschülerinnen in Hamberger Krankenhäusern im Jahre 1979. Monatsschrift Kinderheilkdunde 129:464-466.

              Elias, J, D Wylie, A Yassi, and N Tran. 1993. Eliminating worker exposure to ethylene oxide from hospital sterilizers: An evaluation of cost and effectiveness of an isolation system. Appl Occup Environ Hyg 8(8):687-692.

              Engels, J, TH Senden, and K Hertog. 1993. Working postures of nurses in nursing homes. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Englade J, E Badet and G Becque. 1994. Vigilance et qualité de sommeil des soignants de nuit. Revue de l’infirmière 17:37-48.

              Ernst, E and V Fialka. 1994. Idiopathic low back pain: Present impact, future directions. European Journal of Physical Medicine and Rehabilitation 4:69-72.

              Escribà Agüir, V. 1992. Nurses’ attitudes towards shiftwork and quality of life, Scand J Soc Med 20(2):115-118.

              Escribà Agüir V, S Pérez, F Bolumar, and F Lert. 1992. Retentissement des horaires de travail sur le sommeil des infirmiers. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Estryn-Béhar, M. 1990. Les groupes de parole: Une stratégie d’amélioration des relations avec les malades. Le concours médical 112(8):713-717.

              —. 1991. Guide des risques professionnels du personnel des services de soins. Paris: Editions Lamarre.

              Estryn-Béhar, M and N Bonnet. 1992. Le travail de nuit à l’hôpital. Quelques constats à mieux prendre en compte. Arch Mal Prof 54(8):709-719.

              Estryn-Béhar, M and F Fonchain. 1986. Les troubles du sommeil du personnel hospitalier effectuant un travail de nuit en continu. Arch Mal Prof 47(3):167-172;47(4):241.

              Estryn-Béhar, M and JP Fouillot. 1990a. Etude de la charge physique du personnel soignant, Documents pour le médecin du travail. INRS: 27-33.

              —. 1990b. Etude de la charge mentale et approche de la charge psychique du personnel soignant. Analyse du travail des infirmières et aides-soignantes dans 10 services de soins. Documents pour le médecin du travail INRS 42:131-144.

              Estryn-Béhar, M and C Hakim-Serfaty. 1990. Organisation de l’espace hospitalier. Techn hosp 542:55-63.

              Estryn-Béhar, M and G Milanini. 1992. Concevoir les espaces de travail en services de soins. Technique Hospitalière 557:23-27.

              Estryn-Béhar, M and H Poinsignon. 1989. Travailler à l’hopital. Paris: Berger Levrault.

              Estryn-Béhar, M, C Gadbois, and E Vaichere. 1978. Effets du travail de nuit en équipes fixes sur une population féminine. Résultats d’une enquête dans le secteur hospitalier. Arch Mal Prof 39(9):531-535.

              Estryn-Béhar, M, C Gadbois, E Peigné, A Masson, and V Le Gall. 1989b. Impact of nightshifts on male and female hospital staff, in Shiftwork: Health and Performance, edited by G Costa, G Cesana, K Kogi, and A Wedderburn. Proceedings of the International Symposium on Night and Shift Work. Frankfurt: Peter Lang.

              Estryn-Béhar, M, M Kaminski, and E Peigné. 1990. Strenuous working conditions and musculoskeletal disorders among female hospital workers. Int Arch Occup Environ Health 62:47-57.

              Estryn-Béhar, M, M Kaminski, M Franc, S Fermand, and F Gerstle F. 1978. Grossesse er conditions de travail en milieu hospitalier. Revue franç gynec 73(10) 625-631.

              Estryn-Béhar, M, M Kaminski, E Peigné, N Bonnet, E Vaichère, C Gozlan, S Azoulay, and M Giorgi. 1990. Stress at work and mental health status. Br J Ind Med 47:20-28.

              Estryn-Béhar, M, B Kapitaniak, MC Paoli, E Peigné, and A Masson. 1992. Aptitude for physical exercise in a population of female hospital workers. Int Arch Occup Environ Health 64:131-139.

              Estryn Béhar, M, G Milanini, T Bitot, M Baudet, and MC Rostaing. 1994. La sectorisation des soins: Une organisation, un espace. Gestion hospitalière 338:552-569.

              Estryn-Béhar, M, G Milanini, MM Cantel, P Poirier, P Abriou, and the ICU’s study group. 1995a. Interest of participative ergonomic methodology to improve an intensive care unit. In Occupational Health for Health Care Workers, 2nd edition, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              —. 1995b. Participative ergonomic methodology for the new fitting out of a cardiologic intensive care unit. In Occupational Health for Health Care Workers, 2nd edition, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Estryn-Béhar, M, E Peigné, A Masson, C Girier-Desportes, JJ Guay, D Saurel, JC Pichenot, and J Cavaré. 1989a. Les femmes travaillant à l’hôpital aux différents horaires, qui sont-elles? Que décrivent-elles comme conditions de travail? Que souhaitent-elles? Arch Mal Prof 50(6):622-628.

              Falk, SA and NF Woods. 1973. Hospital noise-levels and potential health hazards, New England J Med 289:774-781.

              Fanger, PO. 1973. Assessment of man’s thermal comfort in practice. Br J Ind Med 30:313-324.

              —. 1992. Sensory characterization of air quality and pollution sources. In Chemical, Microbiological, Health and Comfort Aspects of Indoor Air Quality—State of the Art in SBS, edited by H Knoppel and P Wolkoff. Dordrecht, NL: Kluwer Academic Publishers.

              Favrot-Laurens. 1992. Advanced technologies and work organization of hospital teams. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              —. 1992. Sensory characterization of air quality and pollution sources. In Chemical, Microbiological, Health and Comfort Aspects of Indoor Air Quality—State of the Art in Sick Building Syndrome, edited by H Koppel and P Wolkoff. Brussels and Luxembourg: EEC.

              Ferstandig, LL. 1978. Trace concentrations of anesthetic gases: A critical review of their disease potential. Anesth Analg 57:328-345.

              Finley, GA and AJ Cohen. 1991. Percieved urgency and the anaesthetist: Responses to common operating room monitor alarms. Can J Anaesth 38(8):958-964

              Ford, CV and DK Wentz. 1984. The internship year: A study of sleep, mood states, and psychophysiologic parameters. South Med J 77:1435-1442.

              Friedman, RC, DS Kornfeld, and TJ Bigger. 1971. Psychological problems associated with sleep deprivation in interns. Journal of Medical Education 48:436-441.

              Friele, RD and JJ Knibbe. 1993. Monitoring the barriers with the use of patient lifts in home care as perceived by nursing personnel. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. LandsbergLech: Ecomed Verlag.

              Gadbois, CH. 1981. Aides-soignantes et infirmières de nuit. In Conditions de travail et vie quotidienne. Montrougs: Agence Nationale pour l’Amélioration des Conditions de Travail.

              Gadbois, C, P Bourgeois, MM Goeh-Akue-Gad, J Guillaume, and MA Urbain. 1992. Contraintes temporelles et structure de l’espace dans le processus de travail des équipes de soins. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Games, WP, and W Tatton-Braen. 1987. Hospitals Design and Development. London: Architectural Press.

              Gardner, ER and RC Hall. 1981. The professional stress syndrome. Psychosomatics 22:672-680.

              Gaube, J, H Feucht, R Laufs, D Polywka, E Fingscheidt, and HE Müller. 1993. Hepatitis A, B und C als desmoterische Infecktionen. Gessundheitwesen und Desinfextion 55:246-249.

              Gerberding, JL. N.d. Open trial of Zidovudine Postexposure-chemoprophylaxis in Health Care Workers with Occupational Exposures to Human Immunodeficiency Virus. Skript SFGH.

              —. 1995. Management of occupational exposures to blood-borne viruses. New Engl J Med 332:444-451.

              Ginesta, J. 1989. Gases anestésicos. In Riesgos del Trabajo del Personal Sanitario, edited by JJ Gestal. Madrid: Editorial Interamericana McGraw-Hill.

              Gold, DR, S Rogacz, N Bock, TD Tosteson, TM Baum, FE Speizer, and CA Czeiler. 1992. Rotating shift work, sleep and accidents related to sleepiness in hospital nurses. Am J Public Health 82(7):1011-1014.

              Goldman, LI, MT McDonough, and GP Rosemond. 1972. Stresses affecting surgical performance and learning: Correlation of heart rate, electrocardiogram, and operation simultaneously recorded on videotapes. J Surg Res 12:83-86.

              Graham, C, C Hawkins, and W Blau. 1983. Innovative social work practice in health care: Stress management. In Social Work in a Turbulent World, edited by M Dinerman. Washington, DC: National Association of Social Workers.

              Green, A. 1992. How nurses can ensure the sounds patients hear have a positive rather than negative effect upon recovery and quality of life. Intensive & Critical Care Nursing Journal 8(4):245-248.

              Griffin, WV. 1995. Social worker and agency safety. In Encyclopaedia of Social Work, 19th edition. Washington, DC: National Association of Social Workers.

              Grob, PJ. 1987. Cluster of hepatitis B transmission by a physician. Lancet 339:1218-1220.

              Guardino, X and MG Rosell. 1985. Exposicion laboral a gases anestésicos. In Notas Técnicas de Prevención. No. 141. Barcelona: INSHT.

              —. 1992. Exposure at work to anesthetic gases. A controlled risk? Janus 12:8-10.

              —. 1995. Exposure monitoring to anesthetic gases. In Occupational Health for Health Care Workers, edited by M Hagburg, F Hoffmann, U Stössel, and G Westlander. Solna: National Institute of Occupational Health.

              Hagberg, M, F Hofmann, U Stössel, and G Westlander (eds.). 1993. Occupational Health for Health Care Workers. Landsberg/Lech: Ecomed Verlag.

              Hagberg, M, F Hofmann, U Stössel, and G Westlander (eds.). 1995. Occupational Health for Health Care Workers. Singapore: International Commission on Occupational Health.

              Haigh, R. 1992. The application of ergonomics to the design of workplace in health care buildings in the U.K. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Halm, MA and MA Alpen, 1993. The impact of technology on patient and families. Nursing Clinics of North America 28(2):443-457.

              Harber, P, L Pena, and P Hsu. 1994. Personal history, training, and worksite as predictors of back pain of nurses. Am J Ind Med 25:519-526.

              Hasselhorn, HM. 1994. Antiretrovirale prophylaxe nach kontakt mit HIV-jontaminierten. In Flüssigkeiten in Infektiologie, edited by F Hofmann. Landsberg/Lech: Ecomed Verlag.

              Hasselhorn, HM and E Seidler.1993. Terminal care in Sweden—New aspects of the professional care of dying. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel U, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Heptonstall, J, K Porter, and N Gill. 1993. Occupational Transmission of HIV: Summary of Published Reports. London: Communicable Disease Surveillance Centre AIDS Centre.

              Hesse, A, Lacher A, HU Koch, J Kublosch, V Ghane, and KF Peters. 1996. Update on the latex allergy topic. Hauzarzt 47(11):817-824.

              Ho, DD, T Moudgil, and M Alam. 1989. Quantitation of human immunodeficiency virus type 1 in the blood of infected persons. New Engl J Med 321:1621-1625.

              Hodge, B and JF Thompson. 1990. Noise pollution in the operating theatre. Lancet 335:891-894.

              Hofmann, F and H Berthold. 1989. Zur Hepatitis-B-Gefährdung des Krankenhauspersonals-Möglichkeiten der prae-und postexpositionellen Prophylaxe. Medizinische Welt 40:1294-1301.

              Hofmann, F and U Stössel. 1995. Environmental health in the health care professions: Biological, physical, psychic, and social health hazards. Reviews on Environmental Health 11:41-55.

              Hofmann, F, H Berthold, and G Wehrle. 1992. Immunity to hepatitis A in hospital personnel. Eur J Clin Microbiol Infect Dis 11(12):1195.

              Hofmann, F, U Stössel, and J Klima. 1994. Low back pain in nurses (I). European Journal of Physical and Medical Rehabilitation 4:94-99.

              Hofmann, F, B Sydow, and M Michaelis. 1994a. Mumps—berufliche Gefährdung und Aspekte der epidemiologischen Entwicklung. Gessundheitwesen und Desinfextion 56:453-455.

              —. 1994b. Zur epidemiologischen Bedeutung der Varizellen. Gessundheitwesen und Desinfextion 56:599-601.

              Hofmann, F, G Wehrle, K Berthold, and D Köster. 1992. Hepatitis A as an occupational hazard. Vaccine 10 suppl 1:82-84.

              Hofmann, F, U Stössel, M Michaelis, and A Siegel. 1993. Tuberculosis—Occupational risk for health care workers? In Occupational Health for Health Care Workers, edited by M Hagberg. Landsberg/Lech: Ecomed Verlag.

              Hofmann, F, M Michaelis, A Siegel, and U Stössel. 1994. Wirbelsäulenerkrankungen im Pflegeberuf. Medizinische Grundlagen und Prävention. Landsberg/Lech: Ecomed Verlag.

              Hofmann, F, M Michaelis, M Nübling, and FW Tiller. 1995. European Hepatitis—A Study. Publikation in Vorereitung.

              Hofmann, H and C Kunz. 1990. Low risk of health care workers for infection with hepatitis-C virus. Infection 18:286-288.

              Holbrook, TL, K Grazier, JL Kelsey, and RN Stauffer. 1984. The Frequency of Occurrence, Impact, and Cost of Selected Musculoskeletal Conditions in the United States. Park Ridge, Il: American Academy of Orthopedic Surgeons.

              Hollinger, FB. 1990. Hepatitis B virus. In Virology, edited by BN Fiedles and DM Knipe. New York: Raven Press.

              Hopps, J and P Collins. 1995. Social work profession overview. In Encyclopedia of Social Work, 19th edition. Washington, DC: National Association of Social Workers.

              Hubacova, L, I Borsky, and F Strelka. 1992. Work physiology problems of nurses working in inpatients departments. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Hunt, LW, AF Fransway, CE Reed, LK Miller, RT Jones, MC Swanson, and JW Yunginger. 1995. An epidemic of occupational allergy to latex involving health care workers. J Occup Environ Med 37(10):1204-1209.

              Jacobson, SF and HK MacGrath. 1983. Nurses under Stress. New York: John Wiley & Sons.

              Jacques, CHM, MS Lynch and JS Samkoff. 1990. The effects of sleep loss on cognitive performance of resident physicians. J Fam Pract 30:223-229.

              Jagger, J, EH Hunt, J Brand-Elnagger, and RD Pearson. 1988. Rates of needle-stick injury caused by various devices in a university hospital. New Engl J Med 319:284-288.

              Johnson, JA, RM Buchan, and J S Reif. 1987. Effect of waste anesthetic gas and vapor exposure on reproductive outcome in veterinary personnel. Am Ind Hyg Assoc J 48(1):62-66.

              Jonasson, G, JO Holm, and J Leegard. Rubber allergy: An increasing health problem? Tuidsskr Nor Laegeforen 113(11):1366-1367.

              Kandolin, I. 1993. Burnout of female and male nurses in shiftwork. Ergonomics 36(1/3):141-147.

              Kaplan, RM and RA Deyo. 1988. Back pain in health care workers. In Back Pain in Workers, edited by RA Deyo. Philadelphia, PA: Hanley & Belfus.

              Katz, R. 1983. Causes of death among nurses. Occup Med 45:760-762.

              Kempe, P, M Sauter and I Lindner. 1992. Special characteristics of nurses for the aged who made use of a training program aimed to reduce burn-out symptoms and first results on treatment outcome. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Kerr, JH. 1985. Warning devices. Br J Anaesth 57:696-708.

              Kestin, IG, RB Miller, and CJ Lockhart. 1988. Auditory alarms during anesthesia monitoring. Anesthesiology 69(1):106-109.

              Kinloch-de-los, S, BJ Hirschel, B Hoen, DA Cooper, B Tindall, A Carr, H Sauret, N Clumeck, A Lazzarin, and E Mathiesen. 1995. A controlled trial of Zidovudine in primary human immunodeficiency virus infection. New Engl J Med 333:408-413.

              Kivimäki, M and K Lindström. 1995. The crucial role of the head nurse in a hospital ward. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Klaber Moffet, JA, SM Chase, I Portek, and JR Ennis. 1986. A controlled study to evaluate the efectiveness of the back pain school in the relief of chronic low back pain. Spine 11:120-122.

              Kleczkowski, BM, C Montoya-Aguilar, and NO Nilsson. 1985. Approaches to Planning and Design of Health Care Facilities in Developing Areas. Vol. 5. Geneva: WHO.

              Klein, BR and AJ Platt. 1989. Health Care Facility Planning and Construction. New York: Van Nostrand Reinhold.

              Kelin, R, K Freemann, P Taylor, C Stevens. 1991. Occupational risk for hepatits C virus infection among New York City dentists. Lancet 338:1539-1542.

              Kraus, H. 1970. Clinical Treatment of Back and Neck Pain. New York: McGraw-Hill.

              Kujala, VM and KE Reilula. 1995. Glove-induced dermal and respiratory symptoms among health care workers in one Finnish hospital. Am J Ind Med 28(1):89-98.

              Kurumatani, N, S Koda, S Nakagiri, K Sakai, Y Saito, H Aoyama, M Dejima, and T Moriyama. 1994. The effects of frequently rotating shiftwork on sleep and the family life of hospital nurses. Ergonomics 37:995-1007.

              Lagerlöf, E and E Broberg. 1989. Occupational injuries and diseases. In Occupational Hazards in the Health Professions, edited by DK Brune and C Edling. Boca Raton, FL: CRC Press.

              Lahaye, D, P Jacques, G Moens, and B Viaene. 1993. The registration of medical data obtained by preventive medical examinations on health care workers. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, F, U Stössel and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Lampher, BP, CC Linneman, CG Cannon, MM DeRonde, L Pendy, and LM Kerley. 1994. Hepatitis C virus infection in health care workers: Risk of exposure and infection. Infect Control Hosp Epidemiol 15:745-750.

              Landau, C, S Hall, SA Wartman, and MB Macko. 1986. Stress in social and family relationships during medical residency. Journal of Medical Education 61:654-660.

              Landau, K. 1992. Psycho-physical strain and the burn-out phenomen amongst health care professionals. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Landewe, MBM and HT Schröer. 1993. Development of a new, integrated patient transfer training program—Primary prevention of low back pain. In Occupational Health for Health Care Workers, editeb by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Lange, M. 1931. Die Muskelhärten (Myogelosen). Munich: JF Lehman Verlag.

              Lange, W and KN Masihi. 1986. Durchseuchung mit Hepatitis-A- und B-Virus bei medizinischem Personal. Bundesgesundheitsol 29;183-87.

              Lee, KA. 1992. Self-reported sleep disturbances in employed women. Sleep15(6):493-498.

              Lempereur, JJ. 1992. Prévention des dorso-lombalgies. Influence du vêtement de travail sur le comportement gestuel. Spécifications ergonomiques. Cah Kinésither 156,:4.

              Leppanen, RA and MA Olkinuora. 1987. Psychological stress experienced by health care personnel. Scand J Work Environ Health 13:1-8.

              Lert, F, MJ Marne, and A Gueguen. 1993. Evolution des conditions de travail des infirmières des hôpitaux publics de 1980 à 1990. Revue de l’Epidémiologie et de santé publique 41:16-29.

              Leslie, PJ, JA Williams, C McKenna, G Smith and RC Heading. 1990. Hours, volume, and type of work of preregistration house officers. Brit Med J 300:1038-1041.

              Lettau, LA, HJ Alfred, RH Glew, HA Fields, MJ Alter, R Meyer, SC Hadler, and JE Maynard. 1986. Nosocomial transmission of delta hepatitis. Ann Intern Med 104:631-635.

              Levin, H. 1992. Healthy buildings—Where do we stand, where do we go? In Chemical, Microbiological, Health and Comfort Aspects of Indoor Air Quality: State of the Art in Sick Building Syndrome, edited by H Knoppel and P Wolkoff. Brussels and Luxembourg: EEC.

              Lewittes, LR and VW Marshall. 1989. Fatigue and concerns about quality of care among Ontario interns and residents. Can Med Assoc J 140:21-24.

              Lewy, R. 1990. Employees at Risk: Protection and Health of Health Care Workers. New York: Van Nostrand Reinhold.

              Lindström, A and M Zachrisson. 1973. Ryggbesvär och arbetssoförmaga Ryyggskolan. Ett Försok till mer rationeli fysikalist terapi. Socialmet T 7:419-422.

              Lippert. 1971. Travel in nursing units. Human Factors 13(3):269-282.

              Ljungberg, AS, A Kilbom, and MH Goran. 1989. Occupational lifting by nursing aides and warehouse workers. Ergonomics 32:59-78.

              Llewelyn-Davies, R and J Wecks. 1979. In-patient areas. In Approaches to Planning and Design of Health Care Facilities in Developing Areas, edited by BM Kleczkowski and R Piboleau. Geneva: WHO.

              Loeb, RG, BR Jones, KH Behrman, and RJ Leonard. 1990. Anesthetists cannot identify audible alarms. Anesthesiology 73(3A):538.

              Lotas, MJ. 1992. Effects of light and sound in the neonatal intensive care unit environment on the low-birth-weight infant. NAACOGS Clinical Issues in Perinatal & Womens Health Nursing 3(1):34-44.

              Lurie, HE, B Rank, C Parenti, T Wooley, and W Snoke. 1989. How do house officers spend their nights? A time study of internal medicine house staff on call. New Engl J Med 320:1673-1677.

              Luttman, A, M Jäger, J Sökeland, and W Laurig. 1996. Electromyographical study on surgeons in urology II. Determination of muscular fatigue. Ergonomics 39(2):298-313.

              Makino, S. 1995. Health problems in health care workers in Japan. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsbeg/Lech: Ecomed Verlag.

              Malchaire, JB. 1992. Analysis of the work load of nurses. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Manuaba, A. 1992. Social-cultural approach is a must in designing hospital in developing countries, Indonesia as a case study. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Maruna, H. 1990. Zur Hepatitis-B-Durchseuchung in den Berufen des Gesundheits und Fürsorgewesens der Republik Österreichs, Arbeitsmed. Präventivmed. Sozialmed 25:71-75.

              Matsuda, A. 1992. Ergonomics approach to nursing care in Japan. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              McCall, T. 1988. The impact of long working hours on resident physicians. New Engl J Med 318(12):775-778.

              McCloy, E. 1994. Hepatitis and the EEC Directive. Presented at the 2nd International Conference on Occupational Health for Health Care Workers, Stockholm.

              McCormick, RD, MG Meuch, IG Irunk, and DG Maki. 1991. Epidemiology for hospital sharp injuries: A 14-year prospective study in the pre-AIDS and AIDS era. Am J Med 3B:3015-3075.

              McCue, JD. 1982. The effects of stresses on physicians and their medical practice. New Engl J Med 306:458-463.

              McIntyre, JWR. 1985. Ergonomics: Anaesthetists’ use of auditory alarms in the operating room. Int J Clin Monit Comput 2:47-55

              McKinney, PW, MM Horowitz, and RJ Baxtiola. 1989. Susceptibility of hospital-based health care personnel to varicella zoster virus infection. Am J Infect Control 18:26-30.

              Melleby, A. 1988. Exercise program for a healthy back. In Diagnosis and Treatment of Muscle Pain. Chicago, IL: Quintessence Books.

              Meyer,TJ, SE Eveloff, MS Bauer, WA Schwartz, NS Hill, and PR Millman. 1994. Adverse environmental conditions in the respiratory and medical intensive care unit settings. Chest 105:1211-1216.

              Miller, E, J Vurdien, and P Farrington. 1993. Shift age in chickenpox. Lancet 1:341.

              Miller, JM. 1982. William Stewart Halsted and the use of the surgical rubber glove. Surgery 92:541-543.

              Mitsui, T, K Iwano, K Maskuko, C Yanazaki, H Okamoto, F Tsuda, T Tanaka, and S Mishiros. 1992. Hepatitis C virus infection in medical personnel after needlestick accidents. Hepatology 16:1109-1114.

              Modig, B. 1992. Hospital ergonomics in a biopsychosocial perspective. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Momtahan, K, R Hétu, and B Tansley. 1993. Audibility and identification of auditory alarms in the operating room and intensive care unit. Ergonomics 36(10):1159-1176.

              Momtahan, KL and BW Tansley. 1989. An ergonomic analysis of the auditory alarm signals in the operating room and recovery room. Presented at the Annual Meeting of the Canadian Acoustical Association, 18 October, Halifax, NS.

              Montoliu, MA, V Gonzalez, B Rodriguez, JF Quintana, and L Palenciano.1992. Conditions de travail dans la blanchisserie centrale des grands hôpitaux de Madrid. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Moore, RM, YM Davis, and RG Kaczmarek. 1993. An overview of occupational hazards among veterinarians, with particular reference to pregnant women. Am J Ind Hyg Assoc 54(3):113-120.

              Morel, O. 1994. Les agents des services hospitaliers. Vécu et santé au travail. Arch mal prof 54(7):499-508.

              Nachemson, AL and GBJ Anderson. 1982. Classification of low back pain. Scand J Work Environ Health 8:134-136.

              National Health Service (NHS). 1991a. Design Guide. The Design of Community Hospitals. London: Her Majesty’s Stationery Office.

              —. 1991b. Health Building Note 46: General Medical Practice Premises for the Provision of Primary Health Care Service. London: Her Majesty’s Stationery Office.

              National Institute for Occupational Safety and Health (NIOSH). 1975. Development and Evaluation of Methods for the Elimination of Waste Anesthetic Gases and Vapors in Hospitals. DHEW (NIOSH) Publication No. 75-137. Cincinnati, OH: NIOSH.

              —. 1997a. Control of Occupational Exposure to N2O in the Dentral Operatory. DHEW (NIOSH) Publication No. 77-171. Cincinnati, OH: NIOSH.

              —. 1977b. Criteria for a Recommended Standard: Occupational Exposure to Waste Anesthetic Gases and Vapors. DHEW (NIOSH) Publication No. 77-1409. Cincinnati, OH: NIOSH.

              —. 1988. Guidelines for Protecting the Safety and Health of Health Care Workers. DHHS (NIOSH) Publication No. 88-119. Cincinnati, OH: NIOSH.

              —. 1994. NIOSH Alert: Request for Assistance in Controlling Exposures to Nitrous Oxide during Anesthetic Administration. DHHS (NIOSH) Publication No. 94-100. Cincinnati, OH: NIOSH.

              Niu, MT, DS Stein, and SM Schnittmann. 1993. Primary human immunodeficiency virus type 1 infection: Review of pathogenesis and early treatment interventions in human and animal retrovirus infections. J Infect Dis 168:1490-1501.

              Noweir, MH and MS al-Jiffry. 1991. Study of noise pollution in Jeddah hospitals. Journal of the Egyptian Public Health Association 66 (3/4):291-303.

              Nyman, I and A Knutsson. 1995. Psychosocial wellbeing and sleep quality in hospital night and day workers. In Occuaptional Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Objectif Prévention No spécial. 1994. Le lève personne sur rail au plafond: Outil de travail indispensable. Objectif Prévention 17(2):13-39.

              O’Carroll, TM. 1986. Survey of alarms in an intensive therapy unit. Anaesthesia 41:742-744.

              Occupational Safety and Health Administration (OSHA). 1991. Occupational Exposure to Bloodborne Pathogens: Final Rule. 29 CFR Part 1910.1030. Washington, DC: OSHA.

              Oëler, JM. 1993. Developmental care of low birth weight infants. Nursing Clinics of North America 28(2):289-301.

              Öhling, P and B Estlund. 1995. Working technique for health care workers. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander G. Landsberg/Lech: Ecomed Verlag.

              Ollagnier, E and Lamarche MJ. 1993. Une intervention ergonomique dans un hôpital suisse: Impact sur la santé de l’organisation du personnel et des patients. In Ergonomie et santé, edited by D Ramaciotti and A Bousquet. Actes du XXVIIIe congrès de la SELF. Geneva: SELF.

              Ott, C, M Estryn-Béhar, C Blanpain, A Astier, and G Hazebroucq. 1991. Conditionnement du médicament et erreurs de médication. J Pharm Clin 10:61-66.

              Patkin, M. 1992. Hospital architecture: An ergonomic debacle. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Payer, L. 1988. Medicine and Culture: The Variety of Treatment in the United States, England, West Germany and France. New York: H. Holt.

              Payne, R and J Firth-Cozens (eds.). 1987. Stress in Health Professions. New York: John Wiley & Sons.

              —. 1995. Determination of dinitrogen oxide (N2O) in urine as control to anesthetic exposure. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hoffmann, U Stössel, and G Westlander. Solna: National Institute of Occupational Health.

              Pelikan, JM. 1993. Improving occupational health for health care workers within the health promoting hospital: Experiences from the Vienna WHO model project “health and hospital”. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Pérez, L, R De Andrés, K. Fitch, and R Najera. 1994. Seroconversiones a VIH tras Sanitarios en Europa. Presented at the 2nd Reunión Nacional sobre el SIDA Cáceres.

              Philip, RN, KRT Reinhard, and DB Lackman. 1959. Observations on a mumps epidemic in a “virgin” population. Am J Hyg 69:91-111.

              Pottier, M. 1992. Ergonomie à l’hôpital-hospital ergonomics. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Poulton, EC, GM Hunt, A Carpenter, and RS Edwards. 1978. The performance of junior hospital doctors following reduced sleep and long hours of work. Ergonomics 21:279-295.

              Pöyhönen, T and M Jokinen. 1980. Stress and Other Occupational Health Problems Affecting Hospital Nurses. Vantaa, Finland: Tutkimuksia.

              Raffray, M. 1994. Etude de la charge physique des AS par mesure de la fréquence cardiaque. Objectif soins 26:55-58.

              Ramaciotti, D, S Blaire, A Bousquet, E Conne, V Gonik, E Ollagnier, C Zummermann, and L Zoganas. 1990. Processus de régulation des contraintes économiques physiologiques et sociales pour différents groupes de travail en horaires irréguliers et de nuit. Le travail humain 53(3):193-212.

              Reuben, DB. 1985. Depressive symptoms in medical house officers: Effects of level of training and work rotation. Arch Intern Med 145:286-288.

              Reznick, RK and JR Folse. 1987. Effect of sleep deprivation on the performance of surgical residents. Am J Surg 154:520-52.

              Rhoads, JM.1977. Overwork. JAMA 237:2615-2618.

              Rodary, C and A Gauvain-Piquard 1993. Stress et épuisement professionnel. Objectif soins 16:26-34.

              Roquelaure, Y, A Pottier, and M Pottier. 1992. Approche ergonomique comparative de deux enregistreurs electroencéphalographiques. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Rosell, MG, P Luna, and X Guardino. 1989. Evaluacion y Control de Contaminantes QuPmicos en Hospitales. Technical Document No. 57. Barcelona: INSHT.

              Rubin, R, P Orris, SL Lau, DO Hryhorczuk, S Furner, and R Letz. 1991. Neurobehavioral effects of the on-call experience in housestaff physicians. J Occup Med 33:13-18.

              Saint-Arnaud, L, S Gingras, R Boulard., M Vezina and H Lee-Gosselin. 1992. Les symptômes psychologiques en milieu hospitalier. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Samkoff, JS, CHM Jacques. 1991. A review of studies concerning effects of sleep deprivation and fatigue on residents’ performance. Acad Med 66:687-693.

              Sartori, M, G La Terra, M Aglietta, A Manzin, C Navino, and G Verzetti. 1993. Transmission of hepatitis C via blood splash into conjunctiva. Scand J Infect Dis 25:270-271.

              Saurel, D. 1993. CHSCT Central, Enquete “Rachialgies” Résultats. Paris: Assistance Publique-Höpitaux de Paris, Direction du personnel et des relations sociales.

              Saurel-Cubizolles, MJ, M Hay, and M Estryn-Béhar. 1994. Work in operating rooms and pregnancy outcome among nurses. Int Arch Occup Environ Health 66:235-241.

              Saurel-Cubizolles, MJ, MKaminski, J Llhado-Arkhipoff, C Du Mazaubrum, M Estryn-Behar, C Berthier, M Mouchet, and C Kelfa. 1985. Pregnancy and its outcome among hospital personnel according to occupation and working condition. Journal of Epidemiology and Community Health 39:129-134.

              Schröer, CAP, L De Witte, and H Philipsen. 1993. Effects of shift work on quality of sleep, health complaints and medical consumption of female nurses. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Senevirane, SR, De A and DN Fernando. 1994. Influence of work on pregnancy outcome. Int J Gynecol Obstet VOL: 35-40.

              Shapiro, ET, H Pinsker and JH Shale. 1975. The mentally ill physician as practitioner. JAMA 232(7):725-727.

              Shapiro, RA and T Berland. 1972. Noise in the operating room. New Engl J Med 287(24):1236-1238.

              Shindo, E. 1992. The present condition of nursing ergonomics in Japan. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Siegel, A, M Michaelis, F Hofmann, U Stössel, and W Peinecke. 1993. Use and acceptance of lifting aids in hospitals and geriatric homes. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Smith, MJ, MJ Colligan, IJ Frocki, and DL Tasto. 1979. Occupational injury rates among nurses as a function of shift schedule. Journal of Safety Research 11(4):181-187.

              Smith-Coggins, R, MR Rosekind, S Hurd, and KR Buccino. 1994. Relationship of day versus night sleep to physician performance and mood. Ann Emerg Med 24:928-934.

              Snook, SH. 1988a. Approaches to the control of back pain in industry. In Back Pain in Workers, edited by RA Deyo. Philadelphia: Hanley & Belfus.

              —. 1988b. The costs of back pain in industry. In Back Pain in Workers, edited by RA Deyo. Philadelphia: Hanley & Belfus.

              South, MA, JL Sever, and L Teratogen. 1985. Update: The congenital rubella syndrome. Teratology 31:297-392.

              Spence, AA. 1987. Environmental pollution by inhalation anaesthetics. Br J Anaesth 59:96-103.

              Stellman, JM. 1976. Women’s Work, Women’s Health: Myths and Realities. New York: Pantheon.

              Steppacher, RC and JS Mausner. 1974. Suicide in male and female physicians. JAMA 228(3):323-328.

              Sterling, DA. 1994. Overview of health and safety in the health care environment. In Essentials of Modern Hospital Safety, edited by W Charney. Boca Raton, FL: Lewis Publishers.

              Stoklov, M, P Trouiller, P Stieglitz, Y Lamalle, F Vincent, A Perdrix, C Marka, R de Gaudemaris, JM Mallion, and J Faure. 1983. L’exposition aux gaz anethésiques: Risques et prévention. Sem Hôs 58(29/39):2081-2087.

              Storer, JS, HH Floyd, WL Gill, CW Giusti, and H Ginsberg. 1989. Effects of sleep deprivation on cognitive ability and skills of pediatrics residents. Acad Med 64:29-32.

              Stubbs, DA, PW Buckle, and PM Hudson. 1983. Back pain in the nursing profession; I Epidemiology and pilot methodology. Ergonomics 26:755-765.

              Sundström-Frisk C and M Hellström.1995. The risk of making treatment errors, an occupational stressor. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Swann-D’Emilia, B, JCH Chu, and J Daywalt. 1990. Misadministration of prescribed radiation dose. Medical Dosimetry 15:185-191.

              Sydow, B and F Hofmann. 1994. Unpublished results.

              Tannenbaum, TN and RJ Goldberg. 1985. Exposure to anaesthetic gases and reproductive outcome: A review of epidemiologic literature. J Occup Med 27:659-671.

              Teyssier-Cotte, C, M Rocher, and P Mereau. 1987. Les lits dans les établissements de soins. Documents pour le médecin du travail. INRS 29:27-34.

              Theorell, T. 1989. The psychosocial working environment. In Occupational Hazards in the Health Professions, edited by DK Brune and C Edling. Boca Raton, FL: CRC Press.

              Theorell T. 1993. On the psychosocial environment in care. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech : Ecomed Verlag.

              Tintori, R and M Estryn-Béhar. 1994. Communication: Où, quand, comment? Critères ergonomiques pour améliorer la communication dans les services de soins. Gestions Hospitalières 338:553-561.

              Tintori, R, M Estryn-Behar, J De Fremont, T Besse, P Jacquenot, A Le Vot, and B Kapitaniak. 1994. Evaluation des lits à hauteur variable. Une démarche de recherche en soins infirmiers. Gestions Hospitalières 332:31-37.

              Tokars, JI, R Marcus, DH Culver, CA Schable, PS McKibben, CL Bandea, and DM Bell. 1993. Surveillance of HIV infection and zidovudine use among health care workers after occupational exposure to HIV-infected blood. Ann Intern Med 118:913-919.

              Toomingas, A. 1993. The health situation among Swedish health care workers. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Topf, M. 1992. Effects of personal control over hospital noise on sleep. Research in Nursing & Health 15(1):19-28.

              Tornquist, A and P Ullmark. 1992. Corporate Space and Architecture, Actors and Procedures. Paris: Ministère de l’équipement du logement et des transports.

              Townsend, M. 1994. Just a glove? Br J Theatre Nurs 4(5):7,9-10.

              Tran, N, J Elias, T Rosenber, D Wylie, D Gaborieau, and A Yassi. 1994. Evaluation of waste anesthetic gases, monitoring strategies and corelations between nitrous oxide levels and health symptoms. Am Ind Hyg Assoc J 55(1):36-42.

              Turner, AG, CH King, and G Craddock. 1975. Measuring and reducing noise. Noise profile of hospital shows that even “quiet” areas are too noisy. Hospital JAHA 49:85-89.

              US Preventive Services Task Force. 1989. Guide to Clinical Preventive Services: An Assessment of the Effectiveness of 169 interventions. Baltimore: Williams & Wilkins.

              Vaillant, GE, NC Sorbowale, and C McArthur. 1972. Some psychologic vulnerabilities of physicians. New Engl J Med 287:372-375.

              Vaisman, AI. 1967. Working conditions in surgery and their effects on the health of anesthesiologists. Eskp Khir Anesteziol 12:44-49.

              Valentino, M, MA Pizzichini, F Monaco, and M Governa. 1994. Latex-induced asthma in four healthcare workers in a regional hospital. Occup Med (Oxf) 44(3):161-164.

              Valko, RJ and PJ Clayton. 1975. Depression in the internships. Dis Nerv Syst 36:26-29.

              Van Damme, P and GA Tormanns. 1993. European risk model. In Proceedings of the European Conference on Hepatitis B as an Occupatioonal Hazard. 10-12.

              Van Damme, P, R Vranckx, A Safary, FE Andre, and A Mehevs. 1989. Protective efficacy of a recombinant deoxyribonucleic acid hepatitis B vaccine in institutionalized mentally handicapped clients. Am J Med 87(3A):265-295.

              Van der Star, A and M Voogd. 1992. User participation in the design and evaluation of a new model hospital bed. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Van Deursen, CGL, CAM Mul, PGW Smulders and CR De Winter. 1993. Health and working situation of day nurses compared with a matched group of nurses on rotating shift work. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Van Hogdalem, H. 1990. Design guidelines for architects and users. In Building for People in Hospitals, Workers and Consumers. Luxembourg: European Foundation for the Improvement of Living and Working Conditions.

              Van Wagoner, R and N Maguire. 1977. A study of hearing loss among employees in a large urban hospital. Canadian Journal of Public Health 68:511-512.

              Verhaegen, P, R Cober, DE Smedt, J Dirkx, J Kerstens, D Ryvers, and P Van Daele. 1987. The adaptation of night nurses to different work schedules. Ergonomics 30(9):1301-1309.

              Villeneuve, J. 1992. Une demarche d’ergonomie participative dans le secteur hôspitalier. In Ergonomie à l’hôpital (Hospital ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              —. 1994. PARC: Des fondations solides pour un projet de rénovation ou de construction Objectif prévention (Montreal) 17(5):14-16.

              Wade, JG and WC Stevens. 1981. Isoflurane: An ansaesthetic for the eighties? Anesth Analg 60(9):666-682.

              Wahlen, L. 1992. Noise in the intensive care setting. Canadian Critical Care Nursing Journal, 8/9(4/1):9-10.

              Walz, T, G Askerooth, and M Lynch. 1983. The new upside-down welfare state. In Social Work in a Turbulent World, edited by M Dinerman. Washington, DC: National Association of Social Workers.

              Wands, SE and A Yassi. 1993. Modernization of a laundry processing plant: Is it really an improvement? Appl Ergon 24(6):387-396.

              Weido, AJ and TC Sim. 1995. The burgeoning problem of latex sensitivity. Surgical gloves are only the beginning. Postgrad Med 98(3):173-174,179-182,184.

              Wiesel, SW, HL Feffer, and RH Rothmann. 1985. Industrial Low Back Pain. Charlottesville,VA: Michie.

              Wigaeus Hjelm, E, M Hagberg, and S Hellstrom. 1993. Prevention of musculoskeletal disorders in nursing aides by physical training. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Landsberg/Lech: Ecomed Verlag.

              Wigand, R and Y Grenner. 1988. Personaluntersuchungen auf Immunität gegen Masern, Varizellen und Röteln, Saarländ. Ärztebl 41:479-480.

              Wilkinson, RT, PD Tyler and CA Varey. 1975. Duty hours of young hospital doctors: Effects on the quality of work. J Occup Psychol 48:219-229.

              Willet, KM. 1991. Noise-induced hearing loss in orthopaedic staff. J Bone Joint Surg 73:113-115.

              Williams, M and JD Murphy. 1991. Noise in critical care units: A quality assurance approach. Journal of Nursing Care Quality 6(1):53-59.

              World Health Organization (WHO). 1990. Guidelines on AIDS and First Aid in the Workplace. WHO AIDS Series No. 7. Geneva: WHO.

              —. 1991. Biosafety Guidelines for Diagnostic and Research Laboratories Working with HIV. WHO AIDS Series No. 9. Geneva: WHO.

              —. 1995. Weekly Epidemiological Report (13 January).

              Wugofski, L. 1995. Occupational accident in health care workers—Epidemiology and prevention. In Occupational Health for Health Care Workers, edited by M Hagberg, F Hofmann, U Stössel, and G Westlander. Singapore: International Commission on Occupational Health.

              Yassi, A. 1994. Assault and abuse of health care workers in a large teaching hospital. Can Med Assoc J 151(9):1273-1279.

              Yassi, A and M McGill. 1991. Determinants of blood and body fluid exposure in a large teaching hospital: Hazards of the intermittent intravenous procedure. American Journal of Infection Control 19(3):129-135.

              —. 1995. Efficacy and cost-effectiveness of a needleless intravenous access system. American Journal of Infection Control 22(2):57-64.

              Yassi, A, J Gaborieau, J Elias, and D Willie. 1992. Identification and control of hazardous noise levels in a hospital complex. In Ergonomie à l’hôpital (Hospital Ergonomics), edited by M Estryn-Béhar, C Gadbois, and M Pottier. International Symposium Paris 1991. Toulouse: Editions Octares.

              Yassi, A, D Gaborieau, I Gi